Question about Mitsubishi WS-55511 55" Rear Projection Television

2 Answers

Cable coxail I tore the cable cord out the back of the tv. I need to know what the cable was connected too, so I can solder it back

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers
Re: cable coxail - Mitsubishi WS-55511 55" Rear Projection Television Projection Televisions

Take it to a pro ,break down.

Posted on May 06, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers
Re: cable coxail

It is the RF input into the choices are...

1) Replace / resolder original connector

2) Install new connector

3) Replace tuner-provide make & model for part # of tuner

Please rate this solution....................

Posted on Nov 14, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Hello i have a zenith z46z83d rear projection tv. the power cord clip on end is damaged and the piece that was connected to the board is broken off i can get a connection sometimes by wiggling it around...

There is a easy way to do this if you can solder--notice the power cord has two sides--one side of the wire will be smooth and the other have ridges---

This is a POLARIZED power cord--

whichever side is damaged you can remove the tab--unsolder it and solder both wires to the same place where the tabs were--

The tabs are just there for ease of production--you will have to gain access to the board to do this but DO NOT KEEP WIGGLING THE CORD OR YOU WILL GET INJURED OR DAMAGE THE SET---

Only TWO wires to deal with here---10 minute job once you get access--unplug set before you do this ---you do not need a special tool for this as almost any soldering iron can be used--OBSERVE THE CORD AS YOU DO NOT WANT TO REVERSE THE WIRES----SHOCK HAZARD WILL EXIST.

POLARIZED CORDS CAME ABOUT TO PROTECT PEOPLE FROM GETTING SHOCKED--lamps, and almost every appliance have them---this happened over 50 years ago after a lot of people got injured and some even killed.

Let me know if you need advice or help--I am here to help people--

If this helps you, rate this solution as I do this here for free.


Nov 08, 2009 | Projection Televisions

4 Answers

My cable connector pulled out from the tv and now the tv won't stay on the power button will blank three times and go off what can be the problem?

when the cable got pulled it broke a connection on the board , and thatswhy it won't come on
it will need to be resoldered where the cable was pulled
need more help just ask me!


Oct 26, 2008 | RCA Projection Televisions

4 Answers

37PF9731D/10 Philips TV. On / off button seems to be moving "in" to the TV, making it difficult to switch on / off. I don't want to send it back to the manuf. as it will be gone for 15 days - is...

Check first the power cable.
Check the power button internally is working.
internally there is a fuse or circuit breaker, on the poower supply board near to where power cable hook up, check it out.
Tryu a different socket.

Sep 01, 2008 | Projection Televisions

1 Answer

We do not have the remote,we do have a radio shack 8 in1 univeral remote.which worked good until, we lost sound and picture,can not get into the program.channels change on screen.and home theater shows up...

I removed coxail cable from the tv and connected 3 rca cables between tv and cablebox, now have picture and sound.The problem is still there ,something has blocked out my internal cable connection.
thanks Roy

Oct 07, 2009 | Projection Televisions

2 Answers

Power wont turn on

do you happen to know what model it is? if it is connected to any other external devices, i would remove them and just connect to your cable box and see if it's the tv or not.. if it isn't, i'll need to know more info on your toshiba tv..

Feb 23, 2008 | Toshiba 65HX81 65" Rear Projection...

2 Answers

Pioneer model sd 582hd5 Video goes out

cold solder connections on the video pc board assy.

Aug 23, 2008 | Projection Televisions

1 Answer

Pioneer 58" SD-582HD5 1080i -Rear Proj TV

Like most problems with this model, check and re-solder the connections on the power supply board on the right rear of the tv, just behind where the main power cord goes in. Most problems are around the upper left corner where the white connectors E-12 and others. Check all of them from loose and cold solder solder connections on the board. Hope this helps.

Jun 02, 2008 | Pioneer SD-582HD5 58" Rear Projection...

1 Answer

Broken cable connection inside board

No need to buy a PC board. Have professional tech solder leads back and tighten connector

Apr 19, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Need new power cord

Recommend against soldering the damaged ends together - it's ugly, will never be especially safe, and risks being unreliable too. Have a look at the TV end of the cable. Does it go straight into the TV, or is there a plug that goes into the TV. If there's a plug, just pull it out, take it along to shop that sells TVs and they'll sell you a new one off the shelf. If the cable goes straight into the TV, the solution is just a tiny bit more involved. First, look at the mains plug to check whether it is moulded on, or rewirable. If moulded on, you will need both a new plug, and some flex. If rewireable, you'll only need the flex. Either way, take the cut-off end to Home Depot or somewhere similar and buy something the same shape and size (thickness of the wires is the important thing here). To fit, carefully take the back off the TV and look at how the existing cord was connected and secured before removing it and putting the new one on in exactly the same way. Don't forget to push the wire through the hole in the case (if there is one) before connecting it up. Once the flex is fitted to the TV, fit the plug to the other end. Safety/reliability tip 1 - while the back is off, try not to touch any electrical or electronic components inside the TV other than the power terminals you're supposed to be working on. Saety tip 2 - when renewing a power cord, wire the new cord to the appliance before fitting the plug to the other end of the cord - amazing how many people have helpfully been plugged into the mains in the middle of a job. A.

May 01, 2007 | Mitsubishi VS-60603 60" Rear Projection...

Not finding what you are looking for?
Mitsubishi WS-55511 55" Rear Projection Television Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66451 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides