Question about Vehicle Parts & Accessories

Open Question

My 1998 4Runner is locked by the chapman alarm system from the dealer. I lost my alarm remote controllers but since I kept the alarm on valet it was never a problem until now. Please how do I fix it

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
doin12volt
  • 233 Answers

SOURCE: car starter not working

look under the dash for a small silver toggle switch....this is a disable switch for the remote start portion of the system..you may have kicked it / bumped it with your foot, causing the remote start portion to be deactivated. Just flip the switch the opposite way and try again..
Also, there may have been a pin style switch installed under the hood...Check to see if it is bent or broken, if it is, simply disconnect it and insulate the wire that was going to it. 
This wire is used as a safety to keep the vehicle from remote starting while the hood is up..to keep people from being injured if the remote start is activated while the engine is being worked on. 
Have whatever shop installed the system replace your pinswitch if that is the problem.

Posted on Dec 19, 2008

Ad
  • 265 Answers

SOURCE: car alarm wont turn off

Try changing the batterys in the remotes mate

Posted on Feb 16, 2009

  • 16 Answers

SOURCE: disarming chapman vehicle alarm system on 94 chrysler new yorker

If you have removed the brain, I don't see why you need to remove the rest, unless you just want it out of the car. Without the brain the wiring should cause no problems to your car unless there is a bad connection. If you need more info on how to remove the remaining alarm---
remove the siren in the engine compartment. Most everything else will probably be found under dash drivers side. If it has been installed with connectors, remove them at point of connection. If solderd cut at point of connection and use electrical tape to cover exposed wire. You will have one wire connected to the dome light circuit, one to the parking lights, one to a relay to disable the starter. Cut it out and reconnect starter wire. Led, a switch, maybe a button also-not hard but maybe not necessary?

Posted on Sep 13, 2009

richroth
  • 9472 Answers

SOURCE: I have a PR00E4BS 4-button

Here is a link to the programming guide for the remote Here is a link to the manual Here is a link to the installation guide
richroth_11.gif
Happy Holidays

Posted on Dec 12, 2010

  • 1 Answer

SOURCE: Car Alarm

How to remove the valet off the alarm lost my manual my alarm don't protect my car

Posted on Jul 20, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to program remote for viper 650xv?


You can find a copy of the manual at the link below or try this:

  1. Open driver's door - leave it open (door trigger must be connected on the alarm).
  2. Turn ignition key on.
  3. Within 5 seconds, press the valet/programming button once and release.
  4. Press valet/programming button again and hold it down.
  5. With valet/programming button held down, you should hear the siren chirp within a few seconds. After the chirp, press the lock button on your new remote.
  6. After pressing the remote's lock button, you should hear a short blast from the siren. Now release the valet/programming button.
Viper 650XV Installation Manual

May 13, 2014 | Basic Remote Vehicle Alarm System

1 Answer

My avital 477l starter has some Zs by the car and it won't let me set my alarm. How can I restart starter?


The Zs mean that the alarm is in valet. To exit valet with the remote: open any vehicle door, press lock,unlock,lock. The zs should disappear from the remote allowing you arm the alarm.

Feb 16, 2011 | 477L Ask RXTX HHU Remote

1 Answer

My led light for my alarm stays on and the alarm dont work anymore but the button still locks?unlocks/and starts


Your system is in valet. To take the system out of valet with remote: open any door, press lock, unlock, lock. Now check the LED; it should be off. Close the door and arm the system to check.
OR
Turn the key on then off. Within ten seconds press and release the valet switch. The LED should be off now. Close the door and arm the system. The alarm should chirp to confirm that it is armed.

Nov 26, 2010 | Remote Start System

1 Answer

I have had my Viper system for some years now with never a problem, that is until yesterday. Now when I arm or disarm my system the horn does not chirp and the small red dash light stays solid red instead...


Your alarm is is in valet. to take the alarm out of valet with the remote: open any door. Press lock, unlock, lock. The LED should be off now. Close the door and lock the doors with remote. The alarm should chirp to confirm that it is armed.
OR
Turn the key on then off. Within ten seconds press and release the valet switch. The LED should be off now. Close the door and lock the vehicle with the remote. The alarm should chirp to confirm that it is armed.

Nov 26, 2010 | Remote Start System

1 Answer

I have a viper alarm on my car that wont shut off nor i cant start the car..and i have tried the button under my dash, how Can i shut it off??


was it a professional or shade tree install? the following is off vipers website:
disarming without a remote control
This feature allows you to disarm the security system without the
Remote Control should it be lost, damaged, or disabled. In order to
disarm the system without a remote remote control, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
turn the ignition to the ON position.
Press the Valet button the
preset number of times (one to
five times) within 15 seconds. After five seconds the system will
disarm. If the system does not disarm, you may have waited too long;
turn the ignition off and on and try again.
if that doesn't work try this other

valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the Remote Control, but
all convenience functions (door locks, trunk release, etc.) will
continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
button within 10 seconds.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.

May 08, 2010 | 1994 Honda Civic

2 Answers

My valet remote control RPN491 Starts vehiclr and unlocks doors but will not lock doors do I need to reprogram remoteto unlock doors?


Ok you said "unlock doors' but you said it already unlocks the doors. This remote should lock and unlock door on same button, if you are describing the 2 button remote. If it is not then it could be alot of things. Does the alarm lock itself? Does the alarm lock the door when you turn on the ignition? More info is really needed. Like what veh and what model alarm.

Sep 11, 2009 | DEI Valet Keyless Entry System

1 Answer

Lost keyless remote


take it to a local dodge dealer or a stereo store and they could tell u how to disable the alarm

Nov 29, 2008 | 1994 Dodge Intrepid

2 Answers

Toad sterling car alarm lost manual and need stop code.


This worked on my car when the clicker died:

Put the car in valet mode. Disconnect the NEGATIVE battery terminal. Put the keys in the ignition and turn it as far forward as you can (as though trying to start it) and let it spring back. Reconnect the negative terminal. This should reset the alarm to valet mode. Programming varies from brand to brand. Contact an alarm dealer and they can help reprogram the remote(s).

Oct 17, 2008 | Vehicle Parts & Accessories

2 Answers

Viper auto alarm stuck in valet mode


u can open the drivers door if u have a 2 key remote just press lock aux lock again pretty fast and u should be great.

Oct 15, 2007 | Viper RCVGC022 Remote Control

Not finding what you are looking for?
Vehicle Parts & Accessories Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vehicle Parts & Accessories Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Brad Brown

Level 3 Expert

16231 Answers

Are you a Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...