Question about York Fitness Z16 Treadmill

Open Question

Could you please tell me how to tighten the running matt. It keeps slipping.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust the slip clutch on a heston swather 1360?


Your manual should tell you. Most of time, tighten the nut a little.

Jun 26, 2014 | Garden

1 Answer

Hi my belt is slipping. I have tightened it but it is still slipping. I am concerned that further tightening will result in a too high amp draw on the motor and cause a burn out. Does the deck needs to be...


Hello,

Does the belt stop while walking or running? Does it staop after it has run for a while? Does the motor seem to stop too? or can you hear it running like normal?

Let me know, It is most likley the pully on the front roller.

Matt

Dec 08, 2010 | Epic View 550 Treadmill

1 Answer

My belt needs to be adjusted. I believe it needs ...


If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift the edges of the walking belt (2 to 3 in.) off the walking platform. Be careful to keep the walking belt centred. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

May 20, 2010 | Lamar L-1300 Treadmill by Star Trac - !

2 Answers

Belt is slipping


If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

May 15, 2010 | RTO Image 15.0R Treadmill Walking Belt

1 Answer

I need to tighten the belt, it keeps slipping while walking on it


Unplug unit then remove motor shroud then do the following: If the problem is in the drive belt, either the drive belt will stop when stalled or the front roller will stop when stalled. If the motor, drive belt, and front roller continue to turn when the walking belt is stalled, the problem is with the walking belt slipping on the front roller. If the drive belt continues to turn but the front roller stalls, you may have a broken front roller pulley.

1) Adjusting the running belt if the problem: If the walking belt slips when walked on, UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. off the walking platform. Be careful to keep the walking belt centered.Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
2) Adjusting Drive belt: Find the motor mounts. Many motors in Icon treadmills have a main pivot joint in which a bolt runs the full length of the motor mount. This bolt will require loosening to provide maximum adjustability. Some models have a single jack bolt and others have an auto tensioner. Single jack bolts are the easiest to adjust.

May 14, 2010 | Proform 860 Competitor Treadmill

1 Answer

How do I tighten the belts on my 1991 toyota landcruiser to keep from making any slipping noise? Belt only slips when I'm turning sharp in either direction.


this sounds like the powersteering unit busy saying cheers. check your powersteering fluid is topped up. keeping it topped up would keep this from slipping. the belt is tighten to the right degree. I'm sure it's just the fluid. otherwise an early sign that the powersteering system is packing up. good luck

May 07, 2010 | 1991 Toyota Land Cruiser

1 Answer

Treadmill belt keeps slidding to the side


Here are two solutions one is to get the belt centered on the treadmill and the other is to tighten the belt.

There should be two bolts in the rear of the treadmill, one on each side. These bolts adjust the rear roller of the treadmill. The walking belt will always go to the side that is looser. To get the belt back on track, (if you can start the treadmill so the belt is running) tighten the bolt on the side that the belt has slipped to. Tighten the bolt a little bit at a time. If you tighten the bolt too much, then the belt will go to the other side.

To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.

Apr 08, 2010 | RTO Image 15.0R Treadmill Walking Belt

1 Answer

I have a proform treadmill that slips as soon as i step on track i looked at the belt it looks good how do i tighten up the track


There should be adjustment screws on the back left and right sides. The screws will be horizontal with the tread, and probably need an allen wrench to tighten. If the tread runs straight, tighten each side 1/4 turn at a time to keep them even. Check the tread after each adjustment, and stop as soon as the tread quits slipping.

Sep 08, 2009 | Proform Crosswalk 500 Treadmill

1 Answer

Treadmill belt slipping


To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns. If it takes more than 2 turns then something else is the problem.

Mar 22, 2009 | Reebok Exercise & Fitness

Not finding what you are looking for?
York Fitness Z16 Treadmill Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top York Fitness Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Howard
Howard

Level 2 Expert

115 Answers

Tom Chichester

Level 3 Expert

34789 Answers

Are you a York Fitness Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...