Question about Washing Machines

1 Answer

Hi could someone advise me on why my washing machine wont perform in a cycle yet the programm still runs. ive checked the brushes and their fine.

Fills up with water but no spin and water doesnt drain

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 45 Answers

Control panel that is the programmable Logic control may have gone bad

Posted on Apr 10, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Washing machine wont begin a programme


Hi sam this might help if your beko wma10w washing machine wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor

May 17, 2012 | Beko Washing Machines

1 Answer

Hi I have a Bosch WFL226 MAXX. The wash programmes seem to work OK - the motor operates the drum and the pump works fine and drains the machine. The water level vacuum switch seems ok (it stops it...


Bosch WFL226 MAXX This video will show you how to change the pump washing machine
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.
And don't forget to like us on facebook

Dec 21, 2010 | Washing Machines

1 Answer

WF220 Hotpoint - burning smell + wash cycle stalls?


The burning smell is coming from motor. Also your clutch is bad where you are hearing the rattle/grinding.

Dec 12, 2009 | Hotpoint Aquarius WF220 Front Load Washer

1 Answer

The machine goes through cycle but drum not turning switched cycle and it worked for two washed then drum stopped again


I advise you to remove the motor, and check the brushes in the motor, and check for loose or broken wires at trhe same time.
If brushes o/k, then it is probably going to be something more serious.
This being the case, then it could faulty programmer or similar.
Hope this helps.
Thankyou.

Nov 26, 2009 | Indesit W 123 Front Load Washer

1 Answer

Dryer only blowing cold air, washing cycle fine.


try flipping you breaker off and on 2 or 3 times (hard and fast) if this don't work check element, timer , thermostats and safety switch on motor 2 heavy red wires (check wiring diagram for pin numbers of safety switch)....if this switch goes bad the motor will still run but it wont let power go to element washer motor has heat overload sensor

thumbs up


Aug 17, 2009 | Washing Machines

2 Answers

Beko washing machine wont drain or spin water stays in drum


the pump itself could be blocked or broken check inside pump first for any obstructions

Jul 01, 2009 | Washing Machines

1 Answer

Bosch WFL2450 Washing Machine wont spin cycle


Hi there, this problem sounds as though the carbon brushes are needing replaced or infact just needing to be cleaned of dust or dirt. Its very common for the brushes to be covered in dust and fibres. Im not sure where the brushes will be on this model but I hope this helps you in someway.

Sep 23, 2008 | Washing Machines

2 Answers

Beko WMA 510 stuck on cycle


Hi if your beko WMA 510 washing machine wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor

Sep 05, 2008 | Indesit W 123 Front Load Washer

2 Answers

Hotpoint Aquarius WM 62


Hi, Does the drum turn during the wash cycle? When it comes to the spin cycle does it go through to the end without the drum turning? It sounds like it could be the motor needs new carbon brushes. Regards, Tom.

Apr 03, 2007 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Brad Brown

Level 3 Expert

15628 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...