Question about Maytag MSD2756G Side by Side Refrigerator

1 Answer

Ice/water dispenser --stays on for 4 seconds after removing glass

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 4 Answers

Either the micro switch that is activated when you depress the water paddle or the water valve in the back is faulty. You can put a meter on the two wires at the water solenoid and see if the power drops out before the water stops. If so then the valve is bad. If not then the micro switch is still calling for water and may be sticking.

Posted on May 02, 2015

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: The water dispenser takes about 90 seconds to fill a glass

replace filter

Posted on May 09, 2008

BIKER T
  • 909 Answers

SOURCE: The switch on Maytag water and ice dispenser hangs

Need to enquire from the agents if that dispenser switch is available as a spare part. If so, switch off and strip carefully as logic shows you.

Posted on Sep 24, 2009

  • 1 Answer

SOURCE: Why is the ice maker and water dispensing panel on

I called a repair man to fix this problem - "FixYa" was absolutely useless in this case. Turns out there was a short on the control board and it needed to be replaced.

Posted on Dec 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I "Prime the Water Supply System" refereed to in use and care guide that came with my new Kenmore French Door Bottom Freezer, #253.70413411. Cannot find instructions in the manual only reference to...


Assuming you followed the water line installation directions and you have water available to your new refrigerator/freezer here is the rest of the "priming" info you requested. (basically it tells you how to run a bunch of water through the system by filling cups or glasses to remove any debris and/or air...

Automatic Ice & Water Dispenser
Priming the Water Supply System
1. Begin filling the tank by pressing and holding a drinking glass against the water dispenser paddle. 2. Keep the glass in this position until water comes out of the dispenser. It may take about 1½ minutes. 3. Continue dispensing water for about three minutes to flush the system and plumbing connections of any impurities (stopping to empty the glass as necessary).
Ice Maker Operation & Care After the refrigerator is installed properly and has cooled for several hours, the ice maker can produce ice within 24 hours. The ice maker will fill the ice bin from the rear. You must dispense some ice to force the ice forward in the bin. This will allow the bin to fill completely.
Turning the Fresh Food Ice Maker On and Off Ice production is controlled by the ice maker's On/Off icon on the control panel. Press and hold the "Ice Off" icon for three seconds to turn the ice maker "ON" or "OFF". The ice maker is turned off when the LED above the "Ice Off" icon is illuminated.
Using the Ice Maker after Installation Before making ice for the first time, be sure to prime the water supply system. Air in new plumbing lines can result in two or three empty ice maker cycles. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor.
CAUTION
For proper dispenser operation, recommended water supply pressure should fall between 30 psi and 100 psi. Excessive pressure may cause water filter to malfunction.
NOTE The water dispenser has a built-in device that shuts off the water flow after three minutes of continuous use. To reset this shutoff device, simply release the dispenser paddle.
IMPORTANT On occasion, unusually small ice cubes may be noticed in the bucket or in dispensed ice. This could occur in normal operation of the ice maker. If you start seeing these more frequently, it may be an indication of low water pressure or the water filter needs to be replaced. As the water filter nears the end of its useful life and becomes clogged with particles, less water is delivered to the ice maker during each cycle. Remember, if it's been six months or longer since you last changed your water filter, replace the water filter with a new one. Poor quality household water may require the filter to be changed more frequently.
IMPORTANT Your ice maker is turned on at the factory so it can work as soon as you install your refrigerator. If you cannot connect a water supply, set the ice maker's On/Off icon to Off and turn off the water supply valve; otherwise, the ice maker's fill valve may make a loud chattering noise when it attempts to operate without water.
Hope this helps. Randy

Mar 02, 2015 | Kenmore Refrigerators

1 Answer

Not enought water to ice maker


Can you provide a make & model # for the unit?

Feb 08, 2014 | Refrigerators

1 Answer

Please tell me how to replace the water filter and reset the "change filter" light on my Maytag Refrigerator MSD2756GEB. My light stays red after I change the filter. Thanks


Hello,

The filter status display will help you know when to change your
water filter. When the display reads 10%, order a new filter. It is
recommended that you replace the filter when the display reads 10% OR when water flow to your water dispenser or ice maker decreases.

The filter should be replaced at least every 6 months depending on your water quality and usage.

Step 2
Press the eject button to release the filter from the base grille.

Step 3
Pull the filter straight out.

Step 4

Turn the cap counterclockwise to remove it from the filter. IMPORTANT: Do not discard the cap. It is part of your refrigerator. Keep the cap to use with the replacement filter.

Step 5
Align the ridge on the cap with the arrow on the new filter and
turn the cap until it snaps into place.

Step 6
Remove the protective covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.

Step 7
Push the filter into the base grille. The eject button will pop back out when the filter is fully engaged.

Step 8
Flush the water system. Use a sturdy cup or glass. Depress and hold the
water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat this process until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever. Hold down for 5 seconds and then release for 5 seconds. Do this on/off process for about 2 minutes. This will flush air from the filter and water dispensing system.


Take care......

Aug 13, 2010 | Refrigerators

2 Answers

Water dispenser is not working


Does it make ice? If it makes Ice, then you have water to unit. If No Ice and No Water, check water supply. Otherwise, you could have a bad water valve. Remove valve and the line coming off of valve to water reservoir try to dispense water and if valve is good you should have water coming from valve. (have a bucket or bowl handy to catch water).

Mar 28, 2010 | GE Refrigerators

3 Answers

Water dispenser works, ice maker makes ice but doe not dispense


Remove the ice bucket/container from inside the freezer compartment. Examine underneath at the front of the container to see if ice cubes are lodged between the metal blades. If cubes are caught in this area, they will prevent ice from dropping into the glass/cup.

Feb 22, 2010 | KitchenAid Superba Architect KSCS25INSS...

1 Answer

TFX22CR GE refrigerator TFX22CRXFWW does Not dispense ice.


I had this problem with a similar refrigerator. The problem was the slide switch burns itself especially if you slide it from ice to water while holding the glass in to get ice and water into your glass. Better to slide it to ice, press the glass in to get ice, release the glass to stop the ice, slide the switch to water, then press the glass in again to get water. I "fixed" mine by removing the control panel and soldering some of the connections on the slide switch together so that we now have no crushed ice function, but the ice cubes work again. You can also replace the circuit board in the control panel to restore it to like-new operation. I could not find a place to order just the slide switch.

Not sure if this is the same problem with your unit, but sounds the same.

Dec 06, 2008 | GE Profile 26.6 cu. ft. Side-by-Side...

2 Answers

Replacing water fitting assembly


water dispenser continues to run too long after removing glass

Oct 23, 2008 | Refrigerators

1 Answer

Psc23sgrd ss ice/water dispenser not working


It is possible. When you put hit your glass against the paddle to you hear the switch click? And can you still select between water, cubed, and crushed ice? Also does the light by your glass come on when you but your glass against the paddle?

When you put your glass on the paddle it pushes in a microswitch. That microswitch will power the light if it is working and also sends power to the board you are talking about to dispense ice or water depending on what you have selected.

Nov 03, 2007 | GE Profile PSI23NCR Side by Side...

Not finding what you are looking for?
Maytag MSD2756G Side by Side Refrigerator Logo

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Refrigerators Experts

Bailey's...
Bailey's...

Level 2 Expert

221 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

isaac johny
isaac johny

Level 3 Expert

796 Answers

Are you a Maytag Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...