Question about Bowflex Treadmill Series 7
Error Code LS, Treadmill does not move.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Err LS on Bowflex Treadmill
The machine needs to be re-callibrated. L5 error.
Your speed sensor must have been damaged either during shipping or use. You'll need a new one. If under warranty - give Bowflex a call. They will ship you out a new sensor and guide you through installing it via the phone... re-calibrating the machine... and getting it operational again. It will take about 2 hours.
The instruction book doesn't mention calibration. be sure to not callibrate in metrics, however (there's no way to easily tell the difference - you have to ask) or you'll be strolling like a walk in the park at 5 "mph".
Thanks for using FixY - a FixYa rating is appreciated!!
Posted on Feb 21, 2009
There are two hexagonal screws on either side of the front rollers, and four inset hexagonal screws on the back rollers. Turn it on the lowest speed while turning the ones in front, one at a time. You'll see the tread move from one side to the other. Tightening the screws bring the rollers out, pulling the rubber tread taught, and to the left or right, depending on which screw you're turning at the time. The treads should roughly be the same tension, adjusting both inside and outside front screws for each tread. If you have the dual rear rollers, you'd then have to stop the machine after finishing the fronts and tighten the four inset hexagonal screws on each of the rear rollers. No adjustment per se, just tighten them. If you don't, you'll have a sort of clunking, or clicking noise from the imbalance. The single rear roller is a little different, and the adjustment I believe, can be found on this site:
Posted on May 23, 2009
There are four typical causes for this problem : 1) The walking belt and/or deck are worn. (85% of the
2) The walking belt and/or motor belt are too tight- if you have adjusted either recently. (8% of the time)
3) The motor has lost torque and needs brushes or has demagnetized. (5% of the time)
4) The controller board is dropping output. (2% of the time) . You can do it foryourlsef. However i will give some websites FOR TO CONTACT THEM:
www.unitedassemblers.com + www.treadmildoctor.com
Sincerely. Merry Christmas.
There are four typical causes for this problem :
1) The walking belt and/or deck are worn. (85% of the
Posted on Dec 19, 2011
1) test the power cord for open, break
2) see if there some animal, bid the some wires internal, and get touch with the chassins provoking the short in the machine.
3) replace the blown fuse inside, see the block
4) test the main switch for open or defective.
5) unplugg the machine and see if there c.breaker or fuse are tripp? if does the problem is the c.breaker from your home
6) do NOT use extension cord, and buy some detector spikes, glitch,transient.
God bless you
Posted on Jun 27, 2012
Tips for a great answer:
Dec 13, 2016 | Bowflex Exercise & Fitness
Feb 22, 2016 | Bowflex Treadmill Series 7
Feb 21, 2016 | Bowflex Exercise & Fitness
Oct 30, 2015 | Bowflex Exercise & Fitness
May 06, 2014 | Exercise & Fitness
Jun 09, 2011 | Bowflex Series 3 Treadmill Msrp 129999
Jul 19, 2010 | Bowflex Treadmill Series 7
Feb 21, 2009 | Bowflex Treadmill Series 7
Sep 19, 2015 | Bowflex Treadmill Series 7
Jul 12, 2014 | Bowflex Treadmill Series 7
129 people viewed this question
Usually answered in minutes!