Question about Boating

1 Answer

The trim down works all the time. The trim up only works sometimes.

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 456 Answers

Trim solenoid or switch

Posted on Apr 10, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When tilting the motor down it jumps and bangs until it gets to the trim pistons, what is causing this?


Power Tilt and Trim Maintenance Makes a Difference ...

yamahaoutboards.com/.../power-tilt-and-trim-maintenance-makes-differe...
Tilt and trim adjust the angle of the motor and thus the running surface of the boat, ...the grip on the water, the ability to jump on plane and many other operations ... be around the base of the ram, or drip down around the power tilt and trim motor. ...Sometimes you can bang on the power tilt and trim motor with the head of a ...

Jan 10, 2016 | Boating

1 Answer

Why will trim & tilt on my outboard work sometimes and sometimes it will not?


I would look for a corroded ground wire or a connection that has a corroded connection. Clean all ground and hot lead connections, then seal them from moisture.

Sep 14, 2014 | Cars & Trucks

1 Answer

90 hp Engine trim stuck in the up position can not trim down


Diagnostics is needed to find the source of the problem. You will need at a few tools (to access components), a test-light, and a couple fused jumpers to test the trim motor (if needed). Perform a preliminary inspection. Make sure that nothing obvious is seized or broken. Start at the trim control switch and work back to the trim tab. Bad wiring is the number one failure, then switches, relays, solenoids, motors, and then mechanical components. Sometimes these repairs will go fast and sometimes we need to pray. Prepare for the worse and be patent. If you have more information or questions, please write back, good luck.

Jan 01, 2014 | Water Sport

1 Answer

Turning the key to unlock opens every door except the one I want-the drivers door.The inner knob comes 3/4way up but then seems to catch on something. Occasionally it will work perfectly.Car has new...


Depending on the year of your car, newer cars have a door lock control module. I have found most to be mounted on the rear dash between the speakers.

Feb 01, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

Windshield leak began on passenger side of front seat area about three months ago....appears to be across top edge...runs down inside of windshield when in rains....truck has been parked outside since...


Windshield leaks are very difficult to stop. Not even pros can get it right all the time.

There is a silicone windshield sealant (Pep Boys) which has a consistency allowing it to "run" down into the holes / cracks -- sometimes this works sometimes it doesn't.

Yes, windshield trim will need to be removed...

And, yes, the light fixture should come off from top of vehicle, and "standard" silicone caulk can be used around that fixture to stop leaks.

Charlie

Jan 06, 2011 | Ford F-350 Cars & Trucks

1 Answer

My power window on the drivers side is half way down and won,t go up or down now, but other side works


If you know how to remove the interior door trim take that off. If not there is a post on the site already I had just given directions how to do. Once you have the trim panel off you should be able to see part of the power window motor. If you do take a hammer hit it but not too hard. sometimes they need a bit of a jiggle to get going. try it and if it does not work try again, don't begin to hit it harder each time if it does not work. try a little bit harder if you feel like it but if it still doesnt work it is the power window motor you will need to replace then.

Dec 07, 2010 | 1997 GMC Sierra

2 Answers

Door locks not working properly


This can be caused by the actuators in the lock mechanism failing usually causing the door to remain locked. The boor door can also fail this way, though sometimes the catch sticks (pry off the LR badge, squirt with WD40 and work it a few times to fix that). Replacement requires the whole lock unit to be replaced at a cost of roughly £60 a lock, and a hours work. Helps if you have small hands. It does require a complete strip down of the door, and will need the lock unit, trim panel clips, and a trim removal tool. Clips are a few quid, the tool's usually around a tenner.

Jun 07, 2009 | 2004 Land Rover Discovery

1 Answer

Power trim on 60 hp yamaha quit working


find the solenoid for the trim it will be a the engine or on the trim motor it self get a test lite and find the power wire on the trim motor and with someone pushing the trim button test the hot on the motor if there is no power it is the solenoid if there is power u my have a brush stuck in the trim motor itself but 99% of the time it is the solenoid u can tap the trim motor and see if that gets a result but dont hit hard

May 08, 2009 | Yamaha 12V Air Pump

1 Answer

Volvo-penta aq271c, trim will go down, but not up.no pwr at relay


First check the switch-- does it have power, then check the solenoid to see if it works-- there are two. One is for down, One is for up. If you get power from the solenoid-- outgoing-- check connections going to pump motor.

Mar 28, 2009 | Boating

1 Answer

Pioneer djm 500 trims not working properly


The rotary controls / pot's (especially "low") on DJM500's are nototious for becoming dry jointed, usually a quick resolder of the legs / connections sorts them out.

http://stores.ebay.co.uk/methleykev

Jan 10, 2009 | Pioneer DJm500 Professional DJ Mixer...

Not finding what you are looking for?
Boating Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boating Experts

Steve
Steve

Level 3 Expert

693 Answers

ray gallant

Level 3 Expert

42817 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14793 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...