Question about Televison & Video

1 Answer

By replacing the Timing Control Board (TCON) whether the TV Flicker and Picture Jumping issue will be resolved.

I have removed the TCON board right side cable and tested the picture it is perfectly coming not jump/flicker, when i do similar in left side the picture is flick and jumping, Is it the issue of TCON board, can i buy the TCON board and replace? is it solve my issue please confirm, and also i hope the below link part will suit my TV TCON http://www.buyqual.com/6870c-0368a-lg-logic-board-v6-32-42-47-fhd-tm120hz-v0-6.html

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Televison & ... Master
  • 36,311 Answers

Fixya does not sell parts

Posted on Jul 17, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
premtech
  • 934 Answers

SOURCE: Red noise or flicker on bottom half a plasma screen

The old saying that a pictures is worth a thousand words could have been looking at this one... If the lower screen had been streaked in B&W or bands ran completely through the picture Old Drummer I would suspect the logic board also but that's lower y-board failure.
Bill

Posted on Nov 15, 2007

  • 10 Answers

SOURCE: Flickering and Jumping Picture

The problem in your tv is not external.
The problem is in the power supplies internal filtering.
On the primary side of the power supply main board you will find
a large electrolytic capacitor very near the fuse and the primary transformer( the small one). Next to this capacitor you will find a
large 5 watt diode.( black with a silver band at one end). Next to this you will find one lone 1/4 watt resistor. This resistor in conjuction with large electrolytic capacitor is responcible for the internal filtering of the high voltage side of the board. As your unit heats up( anywhere fron 5 to 30 mins) you will notice horizontal
flickering and prior to that red or green or even purple pixelation.
Check this 1/4 watt resistor for dark discoloration and or a bad solder joint on the solder side of the board. This resistor
is directly responcible for controlling the bias current to the high voltage regulators for the 160 volts DC. At no time should you handle or troubleshoot this board with the line plug in.
Even when this board is powered down that capacitor still holds a charge for up to an hour and can knock your you know what
in your sock. If you do not feel comfortable please take the board to someone else. Hope this helps.

Posted on Feb 03, 2008

  • 191 Answers

SOURCE: sound no picture, which component is tcon board? where all audio/video/cable/hdmi plug in to?

for bn94-00963b go and change your backlight inverter

Posted on Oct 05, 2008

  • 1 Answer

SOURCE: sound no picture, which component is tcon board? where all audio/video/cable/hdmi plug in to?

I have LNS4692D. Returned from vacation, turned tv on - no picture. Tried turning tv off for 4 hours- nothing. Symptoms are: tv is on - no picture , just sound; menu doesn't show, volume bar doesn't show;E.Saving is working - the backlight is changing from lighter to darker.
Found this website and ordered T-con, otherwise known as the LCD panel driver board, p/n# Bn8101286a ( thanks premtech) from partstore.com for $124. Part number BN81-01286A A/S T-CON Board.
Installation:
1.Remove plastic cover. There is an arrow for each screw that needs to be removed. Make sure to unscrew pins next to VGA port. I've spent some time trying to figure out what else is holding the plastic panel until I found this pins.
2. Remove big metal shield in the middle of tv that is covering main components. This shield is being held by small black screws all around it.
At this point you will see cover of T-CON. Here is the picture
http://www.avsforum.com/avs-vb/attachment.php?attachmentid=118863&d=1220531321 (thanks ldac9). Do not attempt to remove that cover yet. Proceed with a next step

3.Remove metal panel that holds main components. Locate big chrome screws that have arrows pointing to them and unscrew them. Remove 2 more screws on the bottom of the panel that holds it together with a box for cables. At this point the main panel will be lose
4. Carefully start lifting the panel. You will see that there are connectors going from components on the panel to components on the lower panel and T-CON. Carefully unplug these components and raise the main panel.
5. Remove 4 screws that holds T-CON cover. Pull the cover so that T-CON is completely exposed. The cover is connected by thin alluminum , don't hesitate to pull it , but don't rip it out.
6. Once T-CON is exposed you will see 2 red ribbons. I've spent some time to figure out how unplug those from old T-CON board. Here is the suggestion. Don't try to pull it out. All you need to do is to lift small plastic lever that is part of a connector. Then ribbon can be slided out. If not sure what to do, see how this is done on the new T-CON. It has a principle of buckle on airplain safety belts.
7. Remove old T-CON and install new you.
8. Follow reverse order.

I've never fixed TV before , but this was totally successful project.

Posted on Nov 19, 2008

  • 1 Answer

SOURCE: Flickering/jumping picture

I HAVE THE SAME PROBLEM. TV WAS FINE UNTIL A FEW MONTHS AGO. OF COURSE ITS OUT OF WARRANTY. FROM WHAT I HAVE READ, AND BEEN TOLD, IT IS THE POWER SUPPLY TO THE UNIT. IT IS DEFECTIVE, OR IT OVERHEATS AND TRIES TO SHUT DOWN. A LAW SUIT IS IN PROGRESS AGAINST WESTINGHOUSE TO RESOLVE THIS MATTER. KINDA REMINDS ME OF THE XBOX 360'S WHEN THEY CAME OUT. ALL YOU CAN DO IS TAKE IT IN FOR SERVICE. OR, YOU CAN KEEP TURNING IT ON AND OFF, LIKE I DO. I HAVE HAD THIS TV ON ALL NIGHT BEFORE WITH NO PROBLEMS. AS SOON AS I START CHANGING STATIONS, OUT IT GOES. GOOD LUCK. WESTINGHOUSE WILL NOT EVEN EMAIL ME. I HAVE TRIED SEVERAL TIMES TO CONTACT THEM. I HAVE HEARD FROM THE LAW FIRM IN CALIFORNIA THAT IS GOING AFTER THEM. GO ONLINE, AND JOIN THE CRUSADE.

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have Luxor tv when I switch it on today the picture was bad flicking and jumping any ideas pleaae


The TCON board or the LCD panel is faulty. Can confirm by replacing the TCON board.

If you wish to get some details; visit the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Jan 27, 2017 | Luxor Televison & Video

1 Answer

How do I fix my Samsung Tv.


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Oct 19, 2016 | Samsung Televison & Video

1 Answer

How do I fix my LG Smart Tv that has sound but no picture?


The tcon board or the LCD panel is faulty . Can confirm by replacing the TCON Board .
If you wish to get some details; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Sep 09, 2016 | LG Televison & Video

1 Answer

LG 50PK950 TV picture problems


It is the problem of T-CON (timing and control board) on your TV.

Re-seat the ribbon cabled connected to the TCON output side carefully.

May 22, 2016 | LG Televison & Video

1 Answer

I have a 2011 Sony bravia LCD TV model kdl 40ex621....I hit power button and red led turns green then switches right back to red and blinks 4 times, I need to know what board to replace. Thank you!!


Hi Loren,
Timing control ( TCon) board seems to be the culprit in this case. Please check the connectors and the cables to and fro TCon before going for the replacement.
Good luck.

Apr 11, 2015 | Sony Televison & Video

2 Answers

Our Phillips flat screen TV picture is split down the middle vertically. One side shows a mirror image of the other side, and then sometimes one side is a lighter shade than the other, when it is full...


This may be due to a faulty Timing Control board (TCON board). I had a similar problem with my Samsung LCD TV picture being split vertically down the middle. The image on both halves appeared fuzzy and in reverse (mirror) including the menus. I replaced the TCON board and the problem was resolved.

Aug 18, 2011 | Televison & Video

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74459 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...