Question about Glastar All Star G8 Grinder

Open Question

Glastar grinders Wiring diagram for this grinder

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Glastar allstar grinder wheel not turning


You may have seized the bearings. Either replace the motor or rebuild using new bearings if the motor even works

Nov 29, 2013 | Glastar Diamond Star Grinder w/extras -...

1 Answer

Vermeer 252 wiring diagram


I need a wiring schematics for a 352 Vermeer stump grinder

Jan 14, 2013 | Vermeer 2006 Sc252 Stump Grinder

1 Answer

How can i rewire a lpg bunn coffe grinder? i ordered it on ebay and the wiring and parts were not connected when it finally came, please help!


the wiring diagram should be inside the grinder pannel.

if not then take modal number and call BUNN
or go to BUNN website

please rate my work

Sep 01, 2011 | Bunn LPG Commercial Coffee Grinder...

1 Answer

I have a 1022w bench grinder with a missing capacitor. The baldor catalog doesn't list the part number or spec for the cap. Nor is there a wiring diagram that shows the connections to the cap. Anyone...


OC3012F12SPCYL OIL CAP 12MFD/370V
Thats number the neccesary part for your grinder 12 mfd think about a fitting size of the capacitor and model if you will know for sure here is the information to get .

http://www.baldor.com/brands/baldor-dodge/contact-us/contact


https://www.baldorvip.com/servlet/productInfoPacket/1022W.pdf

Jun 15, 2017 | Baldor 1022w 10" Bench Grinder, 1 Hp,...

1 Answer

Grinder ceased working. I pulled it apart, found broken wire but had to pull fully apart to correct. Grinder now spins discs off and arcs badly at brushes. I think I have connected wiring wrongly. Can I...


you can try going to Makitatools.com and downloading a breakdown for this tool. If it arcing badly at brushes there could be a wiring problem or damage to the armature, check the wiring first and also the wheel spinning off might mean that you are running in reverse. did you take the field out of it and if so it might be in 180 degrees out. Let me know

Feb 14, 2010 | Makita 9005B 5" Electric Angle Grinder

1 Answer

Older sears bench grinder wont run 1/3 hp model 397 19581


Hi again, OK, Well since I don't have a wiring diagram and the colors don't help. I am also going to assume it is 110VAC. The larger wires are probably the run or primary, it you remember which ones were connected it will help with polarizing. ( getting it to run in the right direction as well as the start and primary working together). You can use the two terminal switch but you should use a three wire cord. Use the switch to break the neutral and ground the case. The connections should be as follows: Connection 1, would have one of the primaries and one of the starts to neutral. Connection 2, the other start to the relay. Connection 3, the coil side of the relay to the remaining primary. ( if the relay has two connections on one end and one on the other it would be the single) Connection 4, the 3rd position on the relay to hot. That is how a split phase is wired. You may find a simple wiring diagram on the net if you type split phase motor wiring diagram. Good Luck to you, this should Fixya!

Mar 04, 2009 | Grinders

Not finding what you are looking for?
Glastar All Star G8 Grinder Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Glastar Saws Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Tom Chichester

Level 3 Expert

39250 Answers

ray gallant

Level 3 Expert

48497 Answers

Are you a Glastar Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...