Question about Kenwood KDC-715S

1 Answer

My stereo i need to know how to install my kenwood kds-715s ido not have a manual can you help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 626 Answers
Re: my stereo

Here is the manual from

Wiring info begins on page 42

Best of Luck.

Posted on Nov 14, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Kdc-715s install diagram

The installation procedure begins on page 41 of the manual.

Aug 04, 2012 | Kenwood KDC-138 FM / AM Receiver

1 Answer

Need wirering diagram for my kenwood hdc-715s.

You can get the wiring diagram on the link below page 42.

Good Luck

Nov 21, 2010 | Kenwood KDC-715S

1 Answer

I have the same problem that the Grtpumpkin solved.

you have a bad flexible cable. it needs to be replaced. unless you are good at soldering i would not recommend you replace it yourself, as the connector needs to be unsoldered from the old cable and resoldered on the new one.

Aug 24, 2009 | Kenwood KDC-715S

1 Answer

Need a user manual plzz

Please click HERE to download Free copy of user manual of Kenwood KDC-715S
Website will require any of your email address to start download file.

Feb 14, 2009 | Kenwood KDC-715S

1 Answer

Faceplate is stuck on protect

hi sounds like you have a speaker issue,
try disconnecting the speakers and reconnecting them one at a time.

either that or the power output stage is faulty


Nov 15, 2008 | Kenwood KDC-715S

1 Answer

Manually opening a Kenwood motorized face

hi if you pop off the top cover you should see a motor on the right hand side, with a flexi cable connected to it, if you unplug the Flrxi from the pcb, you can then use a pp3 (9v) type battery to power up the motor. this will be much esier than manually moving the gears.

be sure to remove the flexi first otherwise you WILL damage the motor driver.



Jul 23, 2008 | Kenwood KDC-715S

1 Answer


The difficult part is I have a KDC-X815 and you have a KDC-7024, so I have no idea how different they are internally/mechanically. But if it's any help, here are the (excellent) instructions I used to repair mine. I was able to find a replacement cable at a local stereo shop that also does stereo repair.

This forum thread has a lot of good info, too:

Jul 23, 2008 | Kenwood KDC-7024 CD Player

2 Answers

Kenwood KDC-715s problem.

the kenwoods with the motorized face platesdevelop one problem with time. the flexable ribbon cable between the main unit & the face plate. as the face open & closes, over time wares out the cable. problem consists of face plate not opening/closing, display missing & and/or some or all buttons not working. note these can also be intermittent problems. typically the part number is located on the cable itself on the side where it pluggs into the main board. since you have a service manual, you should verify it in the manual. good luck.

Dec 03, 2006 | Kenwood KDC-715S

Not finding what you are looking for?
Kenwood KDC-715S Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4681 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides