Question about Hoover Washing Machines

1 Answer

All the program working normal except agitator cycle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hoover Master
  • 5,323 Answers

No agitation or spin? try these:

Motor Coupling If the washer won't spin or agitate the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. It is designed to fail if the washer is overloaded in order to protect both the motor and
Drive Belt If the washer won't spin or agitate, check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't spin or agitate properly.

Drive Motor If the washer won't spin or agitate the drive motor might be defective. This is not common. Check all of the other related parts to this symptom before replacing the motor. If the motor is visibly burned out or physically damaged, replace it.

Stator Assembly If the washer won't spin or agitate the stator assembly might be burned out. The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.

Transmission or clutch assembly not engaging due to going out or slipping.


Door or Lid Latch Assembly If the washer won't spin or agitate the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.

Door Lock Motor and Switch Assembly If the washer won't spin or agitate the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.

Motor Control Board If the washer won't spin or agitate the motor control board might be defective. The motor control board provides power to the motor as well as direction and force. If the motor control board is defective the washer may not work at all or function properly.

Posted on Apr 13, 2015

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

docjohn174
  • 943 Answers

SOURCE: WASHER WON'T SPIN OR AGITATE

hi sorry i, not familiar with that make

Posted on Oct 05, 2008

ned_san_jose
  • 230 Answers

SOURCE: Will not agitate 110 92587210 Kenmore Washer

I have 2 words for you: "dog ears".

the dog aggitation ears are what cause the aggitator to aggitate. Those things wear down and not grab after time.

Pretty easy to change out. You just need to pull the aggitator out and change the 4 little plastic ears. Good luck :)

Posted on Jul 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore 700 series top loader washer. I put it on the normal cycle, the washer fills and agitates for a few minutes (maybe 5) then drains only to fill back up and finish the cycle. Is this normal?


no
some cycle the agitator during the fill cycle to get better distribution of the clothes as it is filling and then shut of the water and proceed to the wash cycle
have a technician check out the program board

Jun 15, 2017 | Kenmore Washing Machines

1 Answer

20922990


michael, try running the wash cycle under different levels eg. normal, delicate etc without a load and see if it agitates.If not, the mechanism has diengaged.

Mar 03, 2014 | Washing Machines

1 Answer

Washer wont agitate, pops breaker


Could be the gears/transmission for the agitate cycle are jammed, the motor then freezers, creates an overload and the breaker pops.

Jan 27, 2014 | Maytag Ensignia MAV4758AWW Top Load Washer

1 Answer

Will not agitate 110 92587210 Kenmore Washer


I have 2 words for you: "dog ears".

the dog aggitation ears are what cause the aggitator to aggitate. Those things wear down and not grab after time.

Pretty easy to change out. You just need to pull the aggitator out and change the 4 little plastic ears. Good luck :)

Jul 13, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Neptune washer will not go past the first wash cycle


All functions operate normally except the machine will not agitate.

The agitator is driven by a couple of different methods. The first is the agitator is splined and slips onto the matching splines of the agitator shaft from the transmission. The second is the use of a bell coupling which is splined to the agitator shaft as well and the agitator snaps onto the coupling. If the agitator does not agitate, first remove the agitator and watch the agitator shaft to see if it is working properly. This will require a small load setting of water and the machine set to run. If the agitator shaft is working properly, it is either the splines on the agitator or the bell coupling that is defective. If the agitator shaft does not work properly, the problem is in the transmission.

Apr 07, 2009 | Maytag Neptune FAV6800AW Top Load Washer

2 Answers

WASHER WON'T SPIN OR AGITATE


Fisher and Paykel pride 5.5. It is about 11 yrs old

Oct 04, 2008 | Washing Machines

1 Answer

Washer make a clicking noise


Zoobs, you could have something stuck under the agitator. The agitator will pull straight off. Grip it on each side and pull up hard, but don't hit yourself in the face. If that don't work, try slipping a belt under it and pull. Check for something caught under it. Another possibility could be the nylon suspension rod socket supports in the back. They will make a noise during agitation if they are dry. Put a little 3 in 1 oil to quite them down. Take the front panel off and check the pulley and belt, see if anything is out of whack. I also often find the motor support hitting the bottom panel during agitation making noise. Take the front panel off and observe during agitation. See if the support is striking the bottom. If so, just bend the bottom panel down. Catriver..post back.

Nov 30, 2006 | GE WHSE5240D ENERGY STAR Super Plus 3.2...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

shaun taylor

Level 3 Expert

1525 Answers

Johnny Ramirez
Johnny Ramirez

Level 2 Expert

116 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...