Question about Janome Memory Craft 200E Embroidery Machines

Open Question

Last night it shut down on me, when I tried to restart it it said RomRestoreMode Very 1.0 Error!!

I have the janome MC200e, the last couple days my machine has been freezing mid pattern, I have had to restart it and forward to the point in the pattern I was to finish. Last night it shut down on me, when I tried to restart it it said RomRestoreMode Very 1.0 Error!! Please help. Thanks

Posted by on

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: Janome Customizer 10000

There are different programs for 350E. I think, you was buy program different.

Posted on Jan 11, 2009

Ad
  • 1 Answer

SOURCE: We have a Janome sew precise machine that we bought new about two

I had the same "problem" with my new machine. I called Janome's customer service and they told me the stitch length dial needs to be on S.S. I did that and it worked!

Posted on Feb 12, 2009

  • 2 Answers

SOURCE: Cannot get a straight stitch

Please check the top tension as well and rethread. I had this problem and after doing the above, everything worked perfectly. Thanks.

Posted on Mar 15, 2009

  • 3741 Answers

SOURCE: My Janome 10000 stopped in

Janmore10000 Stopped Embroidering thenstopped everything just shutting off.
If it is getting no power at all, it is probably a fuse. Thefuse is located in a little black box underneath the base of the machine, butit is NOT an easy job to take the box out, disassemble it, replace the fuse,and then reassemble the whole machine. But in your comment you mentioned that there is power tothe machine that means its not fuse problem.

It stopped embroidering in the middle of a project. the handwheel would notmove at all this means that it wasthread jam. Also check the carriage carriage if it does not move to the rightor left and gor stuck in one position or hardly moving a bit then it is out of calibration.

if your machine is outof calibration it will need to recaliberate . Something is like forcing theneedle through a thread jam would cause this. This is not an expensive repair.But a time consuming repair. Its advisable to get it done by service center,
click this linkdirectly to get the support center help
http://janome.com/index.cfm/ContactUs
--------
This will help. Thanks please keep updated. please dorate the solution positively .thank you for using fixya.

Posted on Nov 29, 2009

bugoy31
  • 1238 Answers

SOURCE: Help. I inherited my mother's

Hi karen!!!

Here is a link on how to thread a janome sewing machine.
To see the result just click the link bellow...

http://blog.ginakdesigns.com/2008/02/20/janome-sewing-tutorial-2-threading-the-machine.aspx


That link will definitely help you with your problem but if not please add a comment.

thank you for using fixya..

Posted on Aug 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Janome 10000


so..it only happens in your house? anything odd about the power coming to your machine? have you tried it on another outlet? that might explain why the dealer can't see the problem...

Mar 11, 2008 | Janome Memory Craft 10000

1 Answer

Can I somehow, either by machine or manually, place the needle on a Janome MC200E, where I need it to be on my embroidery pattern?


I am confused. Could you re-phrase your question?
Can you not just turn the flywheel, on the right, which lowers the needle, into your fabric, adjusting as you manually lower the needle?

Jan 26, 2018 | Janome Sewing Machines

1 Answer

My sewing machine seems to do the same stitch length if I set it on 1 or 4 it doesn't change. I also have to pull the fabric along as the machine does not move it, just sews in the same spot. The machine...


There are a couple of things that could cause this. Your feed dogs could be either low or worn down, so they are not biting into the fabric enough to move it. The presser foot pressure could be set at it's lowest setting and not pressing the fabric firmly against the feed dogs, thereby allowing the feed dogs to slip under the fabric without moving it. You could also have a lubrication issue or a broken part in the stitch length adjustment system. In any case it would probably be best to take it to a reputable sewing machine repair shop in your area for a tune up. That's a great idea anyway after buying any machine second hand.

May 02, 2014 | Janome Sewing Machines

1 Answer

Memory Craft 7000 making terriable noise


the machine is showing it doesn't need oiling or the manual says
it's a self oiling machine?
if the machine is self oiling the DON"T oil the machine.
if you think the noise is from the tension dial,, the try using a can of
air or unwaxed dental floss on the tension dial if you have access
to the tension dial.
or the machine may need to be checked to find why it's making the
noise. the machine may just need some adjustments or a tune-up
depending on when the machine has been serviced last.

Dec 12, 2012 | Janome Memory Craft 5700

1 Answer

How do you disinguage the needle, when fillling the bobbon?


On my MC200e the needle is disengaged automatically when I slide the bobbin winding spindle to the right.

Sep 01, 2012 | Janome MC 4400 Computerized Sewing Machine

1 Answer

Cannot get a straight stitch


Please check the top tension as well and rethread. I had this problem and after doing the above, everything worked perfectly. Thanks.

Mar 03, 2009 | Janome 1600P-DB Mechanical Sewing Machine

1 Answer

Bobbin wont spin


I had the same problem last night but was able to solved it by flipping the plastic bobbin over and re-seating it on the post. This time it clicked in and I was then able to get the post to spin. Good Luck!

Jan 07, 2008 | Janome D'cor Excel 5018

Not finding what you are looking for?
Janome Memory Craft 200E Embroidery Machines Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Janome Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1133 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

194 Answers

Eva Hack

Level 1 Expert

25 Answers

Are you a Janome Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...