Question about Bosch WFVC5440UC Washer

1 Answer

E14 shows up before cycle can complete what does this mean

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 937 Answers

Is there a section on fault finding in the manual? If not, ask Bosch.

Posted on Apr 02, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does E14 mean ?

The code can mean different things .check the manual that came with it . the manual will also show how to do a self test .

Oct 20, 2014 | Bosch 24 in. SGS45E02 / SGS45E08 Exxcel...

1 Answer

My 2400 monitor start's up and work's for 10min. then flash's E14, i have cleaned everything possible and it just does the same thing, over again-E14, what might the problem be?

Sounds like the monitor or video card is going bad. I would try the monitor on another computer and see if it does the same thing. If it does you know the monitor has an issue. If it does not show the E14 then you know the problem is with the Video Card in the computer. To verify that it is the video card, just plug in another monitor and see if it does the same thing with the E14.

Apr 17, 2012 | Computers & Internet

1 Answer

Siemens E14-16 Washing machine is not taking the softener when rinsing and posibly not rinsing completely. the dispenser drawer is clean and flows correctly when filled with water. I have checked the...

Same problem with same Siemens E14-16
Cleaned soap drawer inside out (no more black gunge) but still full of conditioner after full cycle and rinse despite 2 internal valves completely cleared and connected
What could be wrong ?

Feb 13, 2012 | Siemens Washing Machines

3 Answers

E 14 bosch washing machine!! aaagghh

i keep getting E14 on my bosch on my washing machine sometimes it works and other times fills with water then E14 comes up could anyone please help me .......

Mar 04, 2011 | Bosch WFK 2401

1 Answer

Hoover optima oph714ds error code e14

hoover optima oph 7d14 working ok but at end of wash cycle error e14 comes up what does this mean

Dec 24, 2010 | Washing Machines

1 Answer

I have a Frigidaire Front Load Washer during its cycle usually 24 and 16 min into the wash cycle it will stop and beep giving a E10 error message. What does this mean?

The cause of the error is that no cold water is getting through the cold water valve (inside the machine).

The E10 error indicates that one of a group of error codes occurred. The specific code could have been one of the following:
  • E11 - Fill time too long. (See test 1 below)
  • E13 - Water leak in the tub or air leak in the air bell. (See test 2 below)
  • E14 - Dispenser drawer reed switch is open. (See test 3 below)
To recall the specific fault code from this group, follow these steps:
  1. Wake the machine by pressing any button
  2. Wait 5 seconds
  3. Press and hold the Start and Pause/Cancel buttons simultaneously
  4. All LEDs will go blank and after a few seconds the control will signal the stored code
Based on the specific error code, follow the specified test and troubleshooting.
The magnet for the dispenser drawer reed switch is shown in the second image below. If this magnet is missing, you will get the E14 code.
Some of the troubleshooting provided is intended for service technicians. Do not conduct any test or troubleshooting that you are not completely confident that you can safely complete. Unplug the washer before accessing internal components.
That website above directly addresses your issue.

Jun 01, 2010 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Not working right


Thanks for using FixYa. E14 error code means water heating error has occurred and failed heating element.

Please do rate the solution and revert for further assistance.


Aug 28, 2009 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Hotpoint ultima 1200 Wm72 Erroe E14

I think you will find that the error relates to the heating element.
E14 on the Hotpoint WM75E means that there is a problem with the water heating.

Jun 05, 2008 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Error code e14

E14 Dryer temperature probe in short circuit or interrupted

Jan 29, 2007 | Smeg WDI12 Front Load Washer / Dryer

Not finding what you are looking for?
Bosch WFVC5440UC Washer Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3074 Answers


Level 3 Expert

76848 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides