Question about Asko W600

1 Answer

Motor wont start

Machine fills with water then drains and proceeds to S.Have replaced the worn brushes but no joy still doing the same proceeds to s

Posted by on

  • 1 more comment 
  • ben newlands
    ben newlands Apr 01, 2015

    Hi Jhonny does not appear to be anything you sugested to clarify turn machine on temperature at o degrees turn knob to any desired wash program (have tried them all) machine starts fills with water pauses then pumps out water and proceeds to the S on the program knob.Whilst in this position a dull sort knock appears to be comming from the motor or pump ?solenoid

  • Jorge Rendon
    Jorge Rendon Apr 02, 2015

    are u sure its from the motor area? the pumo can also make a noise if it is obstructed but u say it is draining? so therefore THE DRIVE MOTOR- If the washer is making a loud noise the drive motor bearings may have worn out. Washer motors are normally almost silent when they run. If the motor is run without a belt hooked up to it and it's loud it will have to be replaced

  • Jorge Rendon
    Jorge Rendon Apr 02, 2015

    If your washer has a loud banging noise during spin the balance weight may be loose. This weight is to counter act the weight of the motor so you will find the weight directly behind the motor. Sometimes simply tightening the bolts will fix your issue but if the bolts are stripped out get some bolts slightly longer than the original bolt to allow you to put a locking nut on the bottom side of the mounting plate. If the weight is broken replace it.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Asko Master
  • 5,323 Answers

Washer fills with water then drains:
The critical question is. Is the water is just running down the drain but the pump isn't running. If it is being pumped out, and you can hear the pump running just the same as when it's emptying prior to spin then it could be aborting the wash because it is, or it thinks it's overheating. ( due to defective water temperature switch)

If water isn't being pumped out, but just draining away all the time, the washer will keep detecting there isn't enough water inside and top up with more. Modern washing machines should be sophisticated enough to realize something's wrong and abort with an error, but if not, it may continue washing or rinsing for a short while before losing enough water to trigger more coming in again. It can get stuck on this cycle indefinitely and it's called siphoning.
Siphoning occurs when the end of the drain hose is lower than the level of the water inside the washing machine. Try raising the hose and see what happens.
Also the drain hose should have some type of air gap where it fits into the stand pipe. It should not have an air tight fit.
Other switch's to check would be the water inlet valve and the water pressure switch with a multi meter for continuity or OHMS.

Posted on Mar 31, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wpre6100g1wt


there are two possible reasons
1 belt has come off the drum and motor
2 the brushes in the motor have worn down so far that it wont turn.

did it happen all of a sudden, or over did it get worse over a period of time?

May 18, 2014 | LG Washing Machines

2 Answers

My washing machine wont spin


Hi if your Beko Wm & Wma Models washing machine wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor

Apr 12, 2014 | Beko Wm & Wma Models Washing Machine Motor...

2 Answers

Water control valve washer


Hi carl if your Beko WM5140W washing machine wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor

Mar 11, 2014 | Beko WM5140W

2 Answers

Washing machine fills with water but then won't wash, spin or drain


Hi Claire if your beko washing machine wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor

Jan 28, 2014 | Beko Washing Machines

1 Answer

Washing machine makes clicking noise after filling up and wont spin. Kepps on clicking until i force shutdown, which then drains the water away.


hi, the problem you have is the motor carbons (brushes) have worn down ( which is natural if machine is used every day ). the machine fills up with water but there is no motor action. the clicking noise you are hearing is the relay on the pcb sending a signal to the motor to turn, but with the carbons worn, there is no motor action. Easy enough to replace them. UNPLUG machine before any repairs are carried out.

Dec 19, 2013 | Indesit Washing Machines

1 Answer

GE washer wont agitate or spin ?


This could be because the carbon brushes in your motor are worn down. One will need to check the motor to be sure.

The carbon brushes apply electricity to the motor via a split ring comutator.
Over a while the carbon dust can create a short circuit. The motor needs to be looked at and cleaned. Possibly may need to replace the brushes.

Take care!
damnor01

Apr 28, 2012 | GE Washing Machines

1 Answer

MY WASHING MACHINE WONT START WASHING


Could be motor brushes or the motor....

Feb 09, 2010 | Washing Machines

1 Answer

Will not move on from wash to spin & therefore empty


its either your brushes on the motor that are worn out or pump blocked or defective

Jun 23, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

WFD 2460 will not start wash cycle after it has filled with water


Isolate power and water supply and gain access to the main drum motor. Check for condition of carbon brushes by removing them and repla
ce if severely worn. Check wiring loom around motor and right back to module controller. The clicking is obviously power being supplied to motor via the loom to the motor. finally check for any dry solder joints or burnt areas on the circuit board controlling the motor.

Dec 07, 2008 | Bosch Logixx WFT 2806 Front Load...

1 Answer

Mrs E King


sounds like worn motor brushes if it fills drains heats etc but no drum action brushes need replacing not expensive job if machine over 3 years old or older almost certainly brushes.

Jan 13, 2008 | Bosch Logixx WFT 2806 Front Load...

Not finding what you are looking for?
Washing Machines Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1467 Answers

Joseph Hoffmann

Level 3 Expert

1706 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...