Question about Hotpoint Washing Machines

1 Answer

Hotpoint aquarius vtd 60 displaying on but wont start

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Hotpoint Master
  • 1,585 Answers

Check door inter lock

Posted on Apr 17, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: HOW CAN I GET MY HOTPOINT AQUARIUS 1400 - OFF CONSTANT TEST PROGRAM?

This works

To exit the TEST mode, press and hold down the "Start/Cancel" button until ALL of the console lights light up. Press both "Start/Cancel" and On/Off buttons simultaneously until " dOFF " appears in the display. The default setting will now appear and the machine can be used normally.

Posted on Feb 07, 2008

Richie_asg1
  • 1036 Answers

SOURCE: hotpoint aquarius wf340

Hi,
First remove the filter (if you can do this easily) - place a roasting pan under it to catch the water.

If you cannot get to any filter, remove the rear pipe from the waste pipe, and check it is not obstructed.
If it looks good enough, try a hot wash with 1 cup of soda crystals. This should clear any accumulation of grease in the pipes.

If still no good, you may have to open up the machine to clear any internal filter before the pump, and check pump vanes are still intact.

Posted on Nov 05, 2008

  • 234 Answers

SOURCE: hotpoint Aquarius model number WF340P all lights are flashing

First, you need to stop the power to the appliance and wait 2 minutes before re-energizing; this many times resets the logic board and removes crazy actions. 2nd, are all the lights flashing continuously or are they flashing several times then pausing and flashing they same several times again? If they flash nonstop, this may indicate a control board failure. If they flash a certain number of times, this would indicate a fault occurance at some item in the appliance. Your owners manual would usually show this list of flash codes in the trouble shoot section. If you do not have a manual , Call GE (general-electric) and ask to have a manual sent to you; you could also ask about the flash code meaning since this is becoming a more and more prevelant problem and manufactures have been educating their phone help people to know some of these standard answers.
Good luck, Macgivor

Posted on Oct 14, 2009

active209
  • 14 Answers

SOURCE: hotpoint aquarius wf340g will wash put wont spin

check solaniod valve on water pump

Posted on Nov 06, 2009

beltronic205
  • 1456 Answers

SOURCE: hotpoint aquarius wf101 washing machine wont start

fit new door interlock switch not too expesive parts about £15

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint aquarius washing machine displaying tESt +won't do anything


Someone has accidentally pressed some buttons and locked you into test mode.
To get out of it you need to press start, the display should go daft. Press start again and the display should settle down. Now press the on/off button and the start button at the same time and hold them down for a few seconds until the display shows d-end or d-off.
Your machine should now work.

Oct 21, 2012 | Hotpoint Washing Machines

1 Answer

Hotpoint vtd 20 drum is not turning,everything


Hi,
There can be many reasons why your dryer2_bing.gif will not turn...

This tip that I wrote will help you to figure out what is happening...

Dryer2_bing.gif Repair - The Dryer2_bing.gif is not Turning
http://www.fixya.com/support/r4422207-dryer_repair_dryer_not_turning

Dryer Repair ? The dryer will not start
http://www.fixya.com/support/r4460438-dryer_repair_dryer_will_not_start


heatman101

May 11, 2010 | Dryers

1 Answer

I have somehow managed to put my hotpoint aquarius into test mode


To get out of it you need to press start, the display should go daft. Press start again and the display should settle down. Now press the on/off button and the start button at the same time and hold them down for a few seconds until the display shows d-end or d-off.

Mar 15, 2010 | Hotpoint Aquarius WD640 Front Load...

2 Answers

Hotpoint aquarius wd440. Flashing lights


press and hold on off button till the display panel lights up.Then press and hold the on/off button and the start /cancel button together.You will now reset the washing machine settings.And just pick your cycle again

Oct 04, 2009 | Hotpoint Aquarius WD63 Front Load...

1 Answer

I have a hotpoint aquarius sdw60 with the eco 45 light flashing fast and will not reset I have tried turning off the power I have stripped the pump this was clear. then reinstalled it but it is still same


I have a Hotpoint Aquarius SDW 60 The delay 3hr &12hr lights are flashing at the same time. Machine won't start. If the door is slamed shut. It get stuck on the Fast & Prewash 40 degree cycle. and stays there.

Jul 13, 2009 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Testing Shows On Display


press and hold start/cancel button for 5 secs. Thenpress on /offbutton and start/cancel together until Doff is displayed the machine should now be ok

Nov 26, 2008 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

Aquarise + super silent WF 630 1300 spin


to removed test display press and hold start/cancel button for 5 secs. then press on/off and start/cancel together until d-off is displayed then machine will work

Oct 27, 2008 | Hotpoint Aquarius WD640 Front Load...

1 Answer

Hotpoint Aquarius super silent


Try pressing the "on" and "start" button together for over 5 seconds..............or till the display vanishes. You will tell me the result...............vote too.

Mar 17, 2008 | Hotpoint Aquarius WF210 Front Load Washer

2 Answers

HOW CAN I GET MY HOTPOINT AQUARIUS 1400 - OFF CONSTANT TEST PROGRAM?


This works

To exit the TEST mode, press and hold down the "Start/Cancel" button until ALL of the console lights light up. Press both "Start/Cancel" and On/Off buttons simultaneously until " dOFF " appears in the display. The default setting will now appear and the machine can be used normally.

Feb 04, 2008 | Hotpoint Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

freddyfox

Level 2 Expert

236 Answers

ptpumpman

Level 3 Expert

407 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...