I do I fix a printing issue

49.4CF1 = gen firmware error-
Common problem on LJ9000 series. most likely a corrupt file has been sent to print,
How to Clear- switch printer OFF
if the net card is not built into the formatter- then unscrew and remove - remove all network/USB points from printer and then cycle the power- leave the printer disconnected from network and allow to reach ready state( If the machine still shows error- read below) if the machine does clear and reach ready then the error is with a bad file in the Print Spooler Que and may still need to be cleared from the print que (on the PC). If the error does not clear then you may need to Reset the machine - to perform a cold reset.
Switch power ON- Wait until Memory Check is Running( lots of asterisks on screen) whilst the mem check is running press and HOLD the green Tick button, Hold until all Three Heartbeat lights have come on together- let go of the tick button use the scroll buttons to navigate down to Cold Reset select and press tick cold reset is now performed- if this doesnt clear your issue then please contact your service Department and inform them that a new formatter may well be required-this repair can be completed using Belmonte Business Equipment.co.uk

Hi Ok try this it may work.
1.Go Menu
Type in *2864
Type in 10
Code WSW00 shows
Type in 51
Code WSW51 0000001 will show
Try different values, eg change to 000000 or 0000010
BUT remember original code to get back to
To exit type 99
Also can try.
Solution:
· Machine off
· Switch on the machine while holding down the “menu”button until all the leds are flashing on/off. Now you are in “maintenance” mode.
· Press 80
· Press the “mono start” button several times until you see “purge: xxxx”
· Press “2783” in order to reset the purge counter. You will see: “purge:0000”
· Press the "stop" button.
· Press “99” to exit the maintenance mode.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one
All The Best: Pineworks
·

Print a self test diagnostic page to check the status of the black ink and print heads.

To print the self-test diagnostic page

• Control panel: Press (Configuration Page button), or press and hold the (Cancel button) for 3 seconds.

For models that support networks: Press (Configuration Page button).

If these are all showing OK then clean the printheads

To clean the printheads
If printed characters are incomplete, or dots or lines are missing from printouts, ink nozzles might be clogged and you might need to clean the printheads.

NOTE: Cleaning uses ink, so clean the printheads only when necessary.

The cleaning process takes up to 3.5 minutes. Some noise might be generated in the process.
• Control panel: Press and hold (Power button), press (Cancel button) two times, press (Resume button) one time, and release (Power button).

If this fails then replace the black cartridge and run a clean cycle again and then a self test diagnostic then try printing again.

Try to power off your computer and printer and let it stay for 5 minutes. Then turn on your printer and computer to see if pending print jobs we're cancelled.

If the problem still there, you can kill the spool process running on your taskbar. Press control + alt +delete button to open the task bar and delete the process from the processes tab.

Hi..
The service error refers to an hardware issue with the printer.. U can try the following step,if this didnt resolve the issue only option is servicing.

1. Unplug printer.
2. Press and hold SYMBOLS & ENTER/MENU.
3. Continue to hold down the buttons while you plug back in the printer, through the entire
power-on sequence.
4. When display reads PERMANENT STORAGE INITIALIZE or HP LASERJET 3200
release the buttons.

Issue

Printer cover is open

Solution

Close the cover.

Issue

Printer is out of paper

Solution

Insert appropriate media in the In tray.

Issue

Printer has difficulty picking up label media

Solution

• Change the printer's print mode setting.
• Change the printer's paper type selection.
• Use a different brand of label media.

Issue

There is a paper jam

Solution

Follow each of these steps until the problem is resolved:

1. Remove the paper from both paper trays.
2. Press the Power button once. Wait a moment for the paper jam to clear.
3. If printing labels, verify that a label did not become detached while passing through the printer. If the paper jam was not resolved, continue on to the next steps.
4. Remove the rear access door.
5. Remove the paper jam through the opening at the back of the printer.
6. Replace the rear access door.
7. Reload the paper into the paper In tray.
8. Print the document.

Issue

There is a problem with a print cartridge

Solution

Follow each of these steps until the problem is resolved:

1. Remove and then reinsert the print cartridge(s) into the printer.
2. Clean the print cartridges automatically using the Clean Cartridges option in the Printer Assistant.
3. Manually clean the print cartridges and print cartridge cradles:
   • Open the printer cover and wait until the carriage moves to the center.
   • Press the Power button to turn off the printer.
   • Disconnect power cord from the back of the printer.
   • Remove the print cartridges and place them on a piece of paper with the nozzle plate facing up.
   • Lightly moisten a cotton swab with distilled water.
   • Clean the face and edges of the print cartridges with the swab. Do not touch the print cartridge ink nozzles or copper contacts.
   • Wipe the underside of the print cartridge cradle walls using a clean, moistened swab.
   • Reinsert the print cartridges.
   • Close the printer cover.
   • Connect the power cord to the back of the printer.
   • Press the Power button to turn on the printer.
4. Calibrate the print cartridges.
5. If the light is still flashing, replace the print cartridges.

Issue

The print cartridge has partial loss of electrical interface with the carriage connections

Solution

1. Print a printer self-test by holding the power button down with a pencil and opening and closing the top cover four times.
2. Check the nozzle self-test pattern in the self-test print out. If one or more of the solid rectangular areas are missing, an electrical contact problem may be present.
3. Remove and then reinsert the print cartridge(s) into the printer.
4. Print the document.
5. If the problem persists, follow the steps listed above for cleaning the print cartridges and print cartridge cradle.
6. Try printing again. If the problem continues, replace the print cartridges.

~~~~~~~~~
Cyber kaka
~~~~~~~~~

If this happens often and then eventually you are able to get back to work. I'll explain how these printers work.

When you send a print task to the printer, the data that is the construct for your document it resides on the printer in a temporary storage location called RAM. Once the instructions and the data are in RAM hitting the Cancel button will not have an effect until there is a break in the program execution to print. Sometimes nearly all the document will print before it cancels and this may take some time. The Cancel command must intercept a line of prgram execution. So just be patient.

If you need to immediately stop printing for some reason, the best thing is to pull the plug on the printer. Leave it unplugged for some time. As you put the power plug back in, press and Hold Cancel until the printer finishes the startup self check test, otherwise it may just pickup where it left off.

If this is a problem where no matter what you do, and the unplug replug while holding down the Cancel button doesn't clear your problem, unplug the printer again and look next to the digital clock at the bottom right of the PC screen. You may see an icon for your printer there. Double click that and you should see all the printer tasks listed in the printer que. Select all of those and then drop the file menu down and select cancel all or delete all.

Any question I didn't cover, please use the Text Box Comment area below to ask me another question.

Regards,
Worldvet

Hi,

IDS (Ink Delivery System) failure is not related to the print heads at all. It pertains to that delivery system that lies between the Print head and the Ink Tank. Its a Hardware Issue, some ttime it gets fixed by resetting the printer.

Follow the below steps.

POWER DRAIN:-Turn off the printer, Unplug the power cable from printer and from the wall outlet.Press and hold ON buton for 30-60 seconds.


PARTIAL RESET:-Unplug the printer power cable while its ON, press and hold # and 3 button and connect the Power cord while holding.Wait untill the ON light flashes, then release the buttons.

----(for below reset cartridges must be removed out)---------

SEMI_FULL RESET:-Unplug the printer power cable while its ON, press and hold # and 6 button and connect the Power cord while holding.Wait untill the ON light flashes,or wait for 20 seconds,hen release the button.If the printer goes off dont worry release the button and Push the ON button.


FULL NVM RESET:-Take the Ink Cartridges out, Unplug the printer power cable while its ON, press and hold OK/ENTER button and CANCEL button and connect the Power cord while holding the buttons.keep Holding the buttons until the printer goes off ,release the button and Push the ON button.

(Notes - resets will take a while)

Thanks
RIZ

Hi
All you need to do is reset the printer to the factory settings, follow the instructions manual for dell 3000cn steps.

Print the Gradation [ESS] Test Print On the Printer
To print all four 20% toner test prints, perform the following step:
Power off the printer.

Hold down the up and down arrow buttons on the printer and power the printer on.

Press the down arrow button until Test Print appears and press the button.

Press the down arrow until Cyan20% [ESS] appears and press the button.

Press the button. The test print will print.

Press the Cancel button.

Press the down arrow until Magenta20% [ESS] appears and press the button.

Press the button. The test print will print.

Press the Cancel button.

Press the down arrow until Yellow20% [ESS] appears and press the button.

Press the button. The test print will print.

Press the Cancel button.

Press the down arrow until Black20% [ESS] appears and press the button.

Press the button. The test print will print.

Press the Cancel button.
STEP: Clean the contact points on the drum cartridge and the right side of the 3000cn-series / 3100cn printer.

To clean the contact points on the drum cartridge and the right side of the printer, perform the following steps:
Power off the printer.
Unplug the power cable.
Pull to open the front cover, and then lift to open the top cover.
Raise the lever on the top right side of the drum cartridge
Grasp the drum cartridge by the handle and lift up and out
Using a clean, dry, lint-free cloth, wipe the contact points on the drum cartridge
Clean the right side of the drum cartridge.
Using a clean, dry, lint-free cloth, wipe the contact points on the right side of the printer
Insert the drum cartridge.
Close the top and front covers.
Plug in the power cable.
Power on the printer
This should resolve the issue

Hi,
Follow these steps.

Print Quality Problems on 3010cn.
Reset the NVRAM On the 3010cn

To reset the NVRAM, perform the following steps:

1. Press the Menu button.
   
   
2. Press the (down arrow) button on the printer until Configure appears, and then press the (right arrow) button on the printer or (Set) button.
   
   
3. Press on the printer until Maintenance appears, and then press on the printer or .
   
   
4. Press the until Init NVRAM appears, and then press or .
   
   
5. Press Initializing and Restart Printer will appear.
   
   
6. Power off the printer and power back on.

To print the Gradation [ESS] test print, perform the following steps:

1. Power off the printer.
   
   
2. Hold down the up and down arrow buttons on the printer and power the printer on. This will bring up a Customer Mode menu.
   
   
3. Press the down arrow button until Test Print appears and press the button.
   
   
4. Press the down arrow button until Gradation [ESS] appears and press the button.
   
   
5. Press the button. On the LCD, Processing appears and the test page is printed.
   
   
6. Power off the printer and power back on.

To print all four 20% toner test prints, perform the following step:

1. Power off the printer.
   
   
2. Hold down the up and down arrow buttons on the printer and power the printer on.
   
   
3. Press the down arrow button until Test Print appears and press the button.
   
   
4. Press the down arrow until Cyan20% [ESS] appears and press the button.
   
   
5. Press the button. The test print will print.
   
   
6. Press the Cancel button.
   
   
7. Press the down arrow until Magenta20% [ESS] appears and press the button.
   
   
8. Press the button. The test print will print.
   
   
9. Press the Cancel button.
   
   
10. Press the down arrow until Yellow20% [ESS] appears and press the button.
    
    
11. Press the button. The test print will print.
    
    
12. Press the Cancel button.
    
    
13. Press the down arrow until Black20% [ESS] appears and press the button.
    
    
14. Press the button. The test print will print.
    
    
15. Press the Cancel button.
    
    
16. Power off the printer and power back on.

Reseat the drum cartridge, perform the following steps:

1. Power off the printer.
2. Unplug the power cable.
3. Pull to open the front cover and then lift to open the top cover. (Figure 1)
   
   
   
   Figure 1 - Open Front and Top Covers
   
   
4. Raise the lever on the top right side of the drum cartridge. (Figure 2)
   
   
   
   Figure 2 - Raise Lever to Release Drum Cartridge
   
   
5. Grasp the drum cartridge by the handle and lift up and out. (Figure 3)
   
   
   
   Figure 3 - Remove Drum Cartridge
   
   
6. Insert the drum cartridge.
7. Close the top and front covers.
8. Plug in the power cable.
9. Power on the printer.