Question about Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher

2 Answers

Hotpoint dc28 dishwasher

When i switch on the pre-wash lights constantly flashes and sounds if its constantly running the pump to empty water thats not in there

Posted by on

  • 1 more comment 
  • steve56 Aug 11, 2008

    Prewash light flashing and pump constantly running, have switched machine off to try and reset, checked filters and hoses everthing looks fine. Fault happened at the begining of normal wash programme.

  • Anonymous Oct 01, 2008

    when i switch on the pre-wash lights constantly flashes and sounds if its constantly running the pump to empty water...

  • EimearNi Mar 10, 2009

    It's staying in pre-wash mode each time I turn on the dishwasher. I can hear it emptying but the cycle fails to start, it remains in pre-wash.



2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

When turn on the light automatically switches to intense and there is a constant sound of himself

Posted on Nov 30, 2013


Standing water inside washer

Posted on Dec 10, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hotpoint DC28 not washing cancel button
2.check if the door closes securely.
3.since there is water in d/w try running a short cycle.If it works, clean the inside thoroughly to ensure no clogs.

Jan 12, 2014 | Hotpoint 18 in. DC28 Slim-Line Built-in...

1 Answer

Drying light flashes after pre wash cycle

check water temperture might be to low might turn the hot water temperture up, water temperture for best wash is 120 degree

Dec 21, 2017 | Hotpoint 18 in. DC27 Slim-Line Built-in...

1 Answer

Hotpoint BC1450 Light 2 normal flashes

Flashing lights, pump running even when turned off. Had to switch off at the socket. The vibration from the machine had managed to give a quarter turn to the appliance gate valve, the type with the little blue handle. I could see the indentation in the rear rubber panel on the back of the dishwasher. Unscrewed the little blue handle, pushed the machine back in and started working as normal. :)

Oct 07, 2012 | Hotpoint 18 in. BCI45 Slim-Line Built-in...

1 Answer

My adp8352 has 3 flashing lights when i open the door it beeps for about 10 seconds at about 30 sec intervals and it sounds like its stuck on constant drain but there is no water in it????

Try unplugging it and plugging it in again - that might reset the unit. And find an online operator's manual and see if there is information that will guide you - they are usually a free download from manufacturer's website.

Oct 23, 2010 | Hotpoint 18 in. DC28 Slim-Line Built-in...

1 Answer

Diplomat Dishwasher ADP8352 Will not complete wash Cycle

My Diplomat ADP8352 when running a cycle it will run for ages, doesn't seem to get hot. If i switch off the m/c then switch it on again it dumps the water left in the m/c?

any ideas?

Jan 04, 2009 | Hotpoint 18 in. DC28 Slim-Line Built-in...

1 Answer

Hotpoint dishwasher bci450

Here are the eco related error codes for your washer..
1)Light 3 (eco) flashes. Water is present in the flood catching tray at the bottom which usually indicates that there is a leak somewhere. More often than not this is just a pipe with a poor fitting and simply tightening the clip is enough to stop the leak. Our machine had a very slow leak from one pipe (not enough to trigger the alarm) which was fixed in this way. The leak is detected by a small float switch located in the flood catch tray.

Undo 4 screws on the metal plate under the dishwasher 3 at the front 1 at the back, this reveals The pump check the seals are in place on the waste pump.

2) Wash indicator lights 3 + 5 (eco + pre) flashing rapidly. Filter is clogged. Pull out the filter and clean it.
3)Runs for approx. 3 minutes and then stops. Lights 3 + 4 (eco and fast) flash. Probably caused by being plumbed into a hot rather than cold water supply. The incoming water is hotter than required for the wash which causes the machine to cut out. Plumbing the machine into a cold water supply will fix the problem with no apparent long term problems.

May 23, 2008 | Hotpoint 18 in. BCI45 Slim-Line Built-in...

1 Answer

Dishwasher emptying

check the base of the machine and see if it has water in it. if so, this will cause the dishwawsher to pump out all the time. mop out and it shoiuld run. you have a leak and will have to trace it - not always easy

May 08, 2007 | Hotpoint 18 in. DC28 Slim-Line Built-in...

Not finding what you are looking for?
Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher Logo

Related Topics:

488 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

77939 Answers

Brad Brown

Level 3 Expert

16841 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides