Question about RCA RT2250 System

3 Answers

Rca Rt2250 I just got a used system. I tried to use it and it powers fine, but when I hook up the speakers it does not have any sound. I am not 100% sure that I am using it correct, but it doesn't seem that hard. I did connect a antenna to it to mak sure that I have a signal.

Posted by on

  • 4 more comments 
  • Nerds Pc Nov 19, 2007

    I have a RCA RT2250 that turns on too and played for about 30min and just stoped. I noticed a green light on inside that wasn't on before. Some times if I let it stay unplugged for a day it will play certain options like vcr2 but nothing else then that will stop working too.

  • Anonymous Mar 17, 2008


  • btjohnson911 Jul 02, 2008

    RT2250 -- the L and R speaker indicators flash and the sound comes on and goes off in about one second intervals.

  • DOWWNTOWN Dec 27, 2008


  • gabhern1980 Jan 04, 2009

    no sound from any speakers when hooked into tv, or any thing. But when hooked up from tv to 6 Ch DIRECT INPUT, the sound pops on and off...

  • Anonymous Jan 14, 2009

    My RCA RT2250B Receiver has the lights flashing as well. The sound pops on for a second and then off again very sporatically. I do not see a green light on inside ir know about the power amps to resolder. Can anyone give any clearer directions (ie: pictures)?



3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There are a bunch of power amps that run sort of in the center of the main board, to the left of the green light that comes on. There is a factory defect in the soldering of these amps. Just remelt the solder on the amp terminals and it should help

Posted on May 01, 2008


Check power supply capacitors on Main PCB. I had problems with sound on any Surround setting, but ok on Stereo(without subwoofer). I had 2 6800 uF/16 V caps bulged. Replacing them solved my problem.


Posted on Apr 23, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just want to know how I can hook up my 8 ohm speakers to this receiver

Posted on Apr 05, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rca rt2250 no sound

please give us more details, I don't know what reciever you want to use? AM,FM? or some other devices.
but if it's the am,fm reciever well you can find it in your instructions manual how to set it though.
just follow the steps and you will have it..

have a nice tunning
just don't rate me badly^^

make sure your antenna is connected properly..

Feb 17, 2008 | RCA RT2250 System

1 Answer

I have an RCA surround sound system for my Big screen. Lately we have horrible static in the main speaker, is the speaker bad? If I unhook it, the rest of the speakers are fine.

Could be bad, swap it with another channel. if the problem is still in the same speaker the speaker is bad. if it still crackels in the other speaker the problem is in the amp.

Dec 30, 2009 | RCA RT2250 System

1 Answer

RCA 5.1 Surround Sound Receiver Sounds fade in and out

chk how you are hooking up the speaker polarity minus to minus and plus to plus.

Oct 17, 2009 | RCA RT2250 System

1 Answer

I have a DVD player, VCR player, TV all attached to an RCA RT2250 audio/video receiver. All was just fine until 2 days ago when the DVD player would no longer give sound and icons of the speaker system...

It's possibly only needs soldering of the voltage regulators. they are on the main circuit board heat sink (middle of the receiver and can be accessed by the bottom panel.


Dec 21, 2008 | RCA RT2250 System

1 Answer

Hooking up speakers

I'm sure you hooked it up the correct way,This rt2250 is a problem to almost everyone.I have two of them and they both present all types of faults

Jul 27, 2008 | RCA RT2250 System

2 Answers

Power but no sound

hook up the antenna at the back and try to tune-in to your favorite radio station.
read the description at the back of your rca rt2250, how to connect your antenna.
connect it properly and raise up the antenna, put it where the signal is good.

Feb 17, 2008 | RCA RT2250 System

2 Answers

RCA RT2250R P.O.S. no sound

The blinking speakers mean the unit is waiting for an input. It could be that the input section is faulty, but I need more details.

What input is being used?
what speakers are connected and to where?
what is the audio source?

May 20, 2007 | RCA RT2250 System

2 Answers

No sound for rt2250

Your problem is A blown output IC.. This should be taken to an authorized repair center. If you know how to service solid state electronics. Go to amd find an authorized parts house and order your manual from there. Or try If you dont find it online there get the number and call them. Good Luck

Aug 12, 2006 | RCA RT2250 System

1 Answer

RCA RT2250

Make that 3. There must be some kind of date chip in the thing

Dec 22, 2005 | RCA RT2250 System

Not finding what you are looking for?
RCA RT2250 System Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Audio Players & Recorders Experts


Level 3 Expert

102366 Answers

The Knight
The Knight

Level 3 Expert

75017 Answers

Gyula Lacz

Level 3 Expert

484 Answers

Are you a RCA Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides