A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones). click here to download the app (for users in the US for now) and get all the help you need. Good luck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The Automatic Shut Down relay is in the power disatribution center by the battery. It provides power to the ignition coil and the fuel injectors when it is turned on by the computer.Turn key to on and check for apower to the coil on the dark greeen wire. If you have power there, the relay is working. Don't believe it affects the pump on your jeep, but maybe. Do you hear the pump come on for 2 seconds when key is turned to on? It should come on to prime the fuel system, and then shut off. May have to be close to tank when someone turns key to on.
I know this might sound dumb, but it has happened to a lot of people - make sure your floor mat (not even a corner of it) isn't on top of the accelerator pedal. Even the slightest weight can cause the pedal to accelerate enough to be noticeable. Not dumb, it's a good answer. The floor mat can slip forward (and has) in two of our new vehicles when we were driving on the highway. It had worked its way off the anchors and slipped forward, causing the vehicles to accelerate. I put the gearshift in Neutral, pulled off the highway and that was the problem, both times. I don't think it was on top of the gas pedal, underneath, but still pressing or I guess, pulling the pedal down.
All of these are good answers, but if it's an automatic transmission, it might be normal provided the engine performance is ok. Auto trannies have a torque converter stall speed. I have a 96 Cadillac Fleetwood and it will move on its own.
Sounds like the switches got damp when you cleaned it. Let it dry out very thoroughly before you plug it back in. Then set the TIME OF DAY first, and be sure you pay attention to AM/PM if you are not in the 24-hour mode. Next, set the BREW TIME. Once again, heed the AM/PM or you will have nice hot coffee either 12 hours early, or 12 hours late! (I don't know which would be worse.)
As per your problem, that the dehumidifier shuts offautomatically - If yourdehumidifier froze, the compressor will shut off automatically. Allow the iceto melt before emptying the tank and restart the dehumidifier.
Hope this will help you. Good Luck.
During the boot process you will see on the screen to press a certain key to enter setup Press and hold that key during the boot up process to enter BIOS you can load failsafe defaultsor load optimized defaults ,press escape then press f10 to save to cmos to restart or During the boot process tap thef8 button three times this will boot into safe mode where the only things working will be your mouse and keyboard enabling you to attempt to repair your computer Also you might try Turn Off the computer, now as soon as you hit the power button, keep on holding "Alt" key & keep on tapping "F10 key,ie: Alt+F10, it will open the recovery console ,select full factory restore and follow on screen instruction. (Note:this will erase all datas on the computer) hope this helps
tapping the F8 key. The Windows Advanced Options Menu appears. If you
begin tapping the F8 key too soon, some computers display a
error" message. To resolve this, restart the computer and try
that the Safe mode option is selected.
Enter. The computer then begins to start in Safe mode.
are finished with all troubleshooting,
close all programs and restart
the computer as you normally would.
If this does not work you
will probly have to go back to factory settings