Question about Maytag Performa PAV2200

1 Answer

PAVT454EWW Series 22

I know the water pump is out; the problem I am having is order the pump with series 22. Will the series 10 work on this model number.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 240 Answers
Re: PAVT454EWW Series 22

As far as I know, the series 10 should work, but remember, if im not mistaken the series 10 had some issues with the lower race coming loose and causing a serious noise issue. I do believe they fixed that on the 22. Are you buying on-line or through a local dealer? If local dealer, take your old pump with you. If ordering on-line, ask the seller or on-line rep this question as well (even though they will sell you the most expensive one). Like I said, I have swapped them before without problem. Jim

Posted on Nov 15, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Is there a way to reset the computer my bosch 300 nexxt series washer?

turn off THE POWER by c. breaker, wait by 45 seconds, and turn ON again and try it.
God bless you

Jul 10, 2013 | Bosch Nexxt 300 Series WFMC2201UC

1 Answer

I have a Maytag Neptune Model #: MAH5500BWW Serial #: 74920520ZZ The door refuses to close. If I slam it a few times, it eventually closes, locks, and it washes fine. I was considering replacing the lock...

If definitely sounds like you have a door latch problem. Slamming the door repeatedly, however, is probably doing more harm than good. You may be able to get the door to work intermittently for now, but eventually, the lock will stop working altogether.

You are correct. The part numbers ARE based on the Serial Number (series) when it comes to Maytag appliances. If a series is listed next to a part (series 10, for example), the part applies to all appliances that have a serial number beginning with "10" or higher. If an additional series is listed (20, for example), the part applies to all appliance that have a serial number beginning with "20" and higher.


Series 10 (serial numbers beginning with "10 to "19")
Series 20 (serial numbers beginning with "20" to "29")
Series 30 (serial numbers beginning with "30 to "39")

So...using YOUR appliance serial number for this example, if you had a part that had several series listings, you would use the one that matches nearest to your serial number. Say, for example you had a door latch that had three different versions (series 10, 20 and 30). You would use series 30, as the number is the closest to the beginning two digits in your serial number. If your serial number began with "19", for example, you would use series "10", because the first two digits in your serial number do not exceed "20". If only one series number is listed, or if no series number is listed, it applies to ALL washers under that particular model number regardless of serial number. Confused now? So am I.

Based on the information you've provided, the part number for a replacement latch assembly for your washer is: 22004435.

You can purchase replacement parts at any of the following websites:

The first three sites on the list also inclide helpful exploded view parts illustrations to assist you with locating and properly identifying any parts you may need. There are also helpful wiring diagrams included on some sites. Prices vary, so shop and compare.

NOTE: If your model number is not listed on some sites, use the part number from the Sears site as your search criteria. Sometimes certain model numbers do not always appear on parts websites (due to the appliance being too old, recently added model, etc.), but the part numbers generally will, because many parts are interchangeable between model numbers. If you have any questions, please post back and let me know. I hope this helps you.

Apr 26, 2011 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Model MAH4000AWW door leaks. Has hole worn in it.

You will need to go back to your madel number. Look you a series or rev number. 10, 42 or 53. It will have one of these numbers there. This will tell you which part your looking for.

model-number-tag.jpg Please rate solution if helpful. Thanks

Aug 24, 2009 | Washing Machines

1 Answer

Excessive lint/ model 110 series machine works

Too little water too many clothes.Drain pump needs cleaning or replacing.

Jul 12, 2009 | Kenmore Washing Machines

2 Answers

Maytag FAV6800AWW - Major overflow right after starting machine

Hi, If you turn the water source valve on and water starts filling the machine even tho the machine is off, change the inlet valve.
If you have to start the machine so water will fill but, the water does not shut off at the desired level, there is a problem with the water level switch.
I hope this helps you. Please let me know if I can assist you further.


Jun 13, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Kenmore 80 Series draining problem

Check the following before replacing the timer.

1. Clogged drain line or water pump
Check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine).

2. Water Pump
If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Note: if you have a belt driven washer, check the belt(s) for cracks, as this would be a perfect time to replace the belt(s) if needed.

Jun 01, 2009 | Kenmore Washing Machines

2 Answers

Kenmore Series 80 agitate for 10 seconds and pause for several minutes

No, the most is a damaged pump, does it pause in agitation or just spin? I would check the lid switch and timer.

Oct 12, 2008 | Washing Machines

1 Answer

Maytag PAVT454EWW pump 21002240

Don't worry about it, you can install the new pump with out the plate. It will work just fine. They must of redesigned it. I get them this way all the time, Catriver

Sep 22, 2008 | Maytag Performa PAV2200

3 Answers

Kenmore Washing Machine 70 series

When this machine is not spinning, the water should still be able to drain, as the motor drives the pump on the same shaft as the coupler for the tranny. Set to the spin setting and depress the lid switch, if the water still does not drain, you may have something stuck in your pump, which would also lock the motor shaft and not allow it to spin or agitate. If the water does drain, check the motor coupler, which is located between the motor and transmission, if broken, the motor will run but there is no drive to the transmission. Hope this helps...

Sep 14, 2008 | Kenmore 20722

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

445 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides