Question about Allied Telesyn AT MR420T (AT-MR420T) Networking Hub

1 Answer


Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 51 Answers
Re: AT-MR420T

Please switch on your hub then place one end of the patch cable in a hub port then another one in the routers switch port Thats all..

Thank you...

Posted on Jan 04, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

D2CIM-VUSB can use USB 1.0?

They should work, but I would use the PS2 connectors to be sure.

May 15, 2014 | Raritan Computer KVM Extenders...

2 Answers

I work at a school and we are trying to connect 2 HP 3com Baseline switch 3952 together. however when I plug in my Cisco SFP modules into both the switches, neither of the ports light up and establish a...

1.what type of fiber is:SM (single mode) or MM (multi mode)?
2.what type of sfp? 1550 or 1310 if is SM, how many conectors and what type of conectors 3com usualy u dont need to make a port anouncemant as u need in cisco so if the sfp are ok, i mean if they are pairs and the fiber is same type should work, second problem : sometime the cisco sfp(when is not original from cisco) got problem in other brands hapend to me whit zyxel sw,

so give me more data and i will help you


Sep 22, 2011 | 3Com Baseline Plus 2952 52 Port Gigabit...

3 Answers

Have HP Procurve 2650 switch with some cisco wireless accespoints (WAP2000) attached. when roaming the user-device from one AP to the other, network connectivity is lost for quiet a while, when APs are...

What I saw is that you can only set it to three roaming types, (PMK Caching, Opportunistic Key Caching, PreAuthentication).

Try to turn them all on and see what happens. Here is a screen shot for it.

Aug 05, 2011 | HEWLETT-PACKARD ProCurve 2650 Stackable...

2 Answers

I need to design a net work for a company with 4 subnets and each subnet work have about 30 hosts. I've chosen a star topology for each sub network. what is the best centralized device should I...

You are going to want to use a switch. the reason you will want to use the switch is because of the different subnets that you will have and the hosts that you are going to have. You will have faster and more reliable connection. With a Router or a HUB the connection will get over worked and you will see the time it takes to do something is that much longer. Always use switches with more then 15 hosts

Jan 02, 2010 | Cisco (NO RETURN) CAT3750 24 10/100 POE +...

1 Answer

Lost Power Adapter for Unicom Mini-switch/8 8 port

method 1: buy a power adapter that has a switch controlled output voltage - they usually have 3V - 4.5V - 6V - 7.5V - 9V and 12V selectable output. Start with 6V and if its not working unplug, select 9 and try again etc. etc.

method 2: open the case and locate an electrolytic capacitor right near the power plug - the biggest one. Note the voltage (for example it may say: 1000uF/15V) and have in mind that your device MUST work at a LOWER level that this.

you can combine the two methods to be safe...

Oct 02, 2009 | Port Incorporated 8-port 100Base-TX Mini...

4 Answers

When switch on the power ,network switch 24port has geting hung

I had a DES-1024D 24 port D-Link (DLINK DES1024D) switch that simply didn't power up one day. I decided to open it up and look and I noticed that on the circuit board of the builtin power supply (which was an SB10-033100-10 according to the label, 3.3V 2.5A switch mode power supply) there was a bloated capacitor. We have seen this often on motherboards in the past. Therer were 2 electrolytic capacitors at the very edge of the circuit board closest to the front panel of the switch that were 1000uf 10V. The metal tops of these should be perfectly flat and one was bulging upward. I replaced both of these caps and the switch powered up fine after that.

Aug 11, 2009 | D-Link DES-1024D Express EtherNetwork...

2 Answers

Need to know power requirements for the kensington k33141 usb hub

i believe i know the answer. i have the kensington pocket hub se 2.0 model: k33141. it seemed to work with the adapter i found in our closet. it is a dve Model : dsa-0131f-05 us 13 and it outputs 5v 2.5a. the adapter has a thin profiile like it would be plugged into a strip. and it has an rf blocker which suggests computer equipment.

Apr 05, 2009 | Kensington (1500100) Networking Hub

1 Answer

Got an accton eh 2024 etherhub and wanna network 2 computers

Forget Windows XP networking wizard.Go to control panel>network connections>right-click on LAN connection>properties>select TCP/IP>click properties IP: the other PC's IP: allow file sharing go to Control Panel>windows firewall>check file and printer sharing and click ok

Mar 27, 2009 | Accton EtherHub 24S (EH2024) Networking...

1 Answer


check mouse ps/2 port connector pins they can be twisted or blunt.

May 03, 2008 | USB, USB 2.0, Parallel,...

2 Answers

Wiring a double throw switch in a house

when working with eletricity always make sure to turn the power off !!!! and test for voltage b4 you start working on the wire
here is a diagram that seems easy to understand:

if you need help on testing the wires to find out which one is which with a ohm meter just ask

Mar 31, 2008 | Networking Hubs & Switches

Not finding what you are looking for?
Allied Telesyn AT MR420T (AT-MR420T) Networking Hub Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Allied Telesyn Networking Hubs & Switches Experts

 Mike M
Mike M

Level 3 Expert

3320 Answers


Level 3 Expert

2072 Answers

The Knight
The Knight

Level 3 Expert

66518 Answers

Are you an Allied Telesyn Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides