Question about Compaq ProLiant 1600 (315570-001) Server

1 Answer

102 error system timer error

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 624 Answers
Re: 102 error

As you probably already know this is a check that happens during the POST process and will halt the boot process. This is a system board failure, not typically user repairable.

Posted on Dec 02, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

I t will satrt up an run but computer keep shuiting down

It could be a couple of things 1. the computer Cpu fan is not working or is clogged inspect it and clean or replace.2 The power supply could be bad

Apr 05, 2014 | Dell PowerEdge Computer Servers

1 Answer

PSU @ PS0 has FAILED. error

you haved answered on your own

Mar 25, 2014 | Sun Netra 240 Server

1 Answer

Parity error System Halted

A Parity error is a memory problem. With a server it is important to have matched sticks of memory. It may just be that one chip is slightly slow/fast compared to all the others. You just need to find it!

Apr 29, 2013 | Acer Altos G530 Server

1 Answer

Sel full 1912 error


You will get the "Sel Full 1912 error" on your server when the system event log is full and unable to record further events. You must clear the event log before the error will cancel. Boot your system into the BIOS/CMOS, locate the system logs and select clear log, reboot your system. Once the system is back up, I would go into the admin task folder and make sure the logs are clear there as well.

Good Luck.

Please rate my solutions here on

Jan 01, 2012 | Dell PowerEdge 2950 (becwfk1_6) Server

1 Answer

IBM xseries eserver x236 Bios problem: a yellow light( !) like this is on and IBM server can not start


Try this:

Light path diagnostics

Many errors are first indicated by the illumination of the system-error light in the operator information panel on the front of the server. One or more lights inside the server might also be lit that can direct you to the source of the error. The system information LED lights to alert you that there might be important information recorded in the system-error log. 2. Removing the left-side cover and look at the light panel. These LEDs indicate the type of error that has occurred.3. Once you know the general type of error and the general location of the component involved, the next step is to check the system service label on the outside of the server. This label gives an overview of internal components that correspond to many of the LEDs on the light path diagnostics panel and can help to view lit LEDs inside the server. Note: Some of the LEDs on the light path diagnostics panel will not have a corresponding LED lit on the system board.

Good Luck

Dec 31, 2010 | IBM eServer xSeries 236

1 Answer

POST errors forcing server to crash

Its best you log a case with HP support. If your system is still under warranty or if you bought support along with the system, they will fix the problem for you.

Apr 01, 2010 | HP ProLiant DL380 G5 Server

1 Answer

Problem rebooting Dell PowerEdge Server 2600

ERROR 02A2: BMC System Error Log (SEL) Full
press F1 to continue or F10 to enter BIOS.
I wait for 2 minutes without doing any thing my server get started normally.
Please help me how to stop this error

Feb 19, 2010 | Dell PowerEdge 2650 Server

2 Answers

Server error

The System Event Log may become full of erroneous IPMI Events reported by the System BIOS. When this occurs, the following message may appear during Power-On Self-Test (POST) and POST cannot continue without user input:
02a2: BMC System Error Log (SEL) Full
Press F1 to Continue, Press F2 to Setup
If the above message appears during POST, perform the following steps to run BIOS setup and delete the System Event Log:
  1. Boot the server and press the F10 key when prompted to run BIOS Setup.
  2. Select the "Advanced" menu.
  3. Scroll down to "IPMI" and press the ENTER key
  4. Scroll down to the System Event Log and press the ENTER key.
  5. At the "Clear System Event Log" selection, press the ENTER key to toggle between "Enable" and "Disable."
  6. Select "Enable."
  7. Press the F10 key to Save the changes and exit the BIOS Setup.

Mar 02, 2009 | HP Compaq ProLiant ML110 G4 Server

1 Answer

02A2: BMC System Event Log(SEL) Full

In HP prolliant server sets, setup also logs system events. This error is due to that log. Enter setup, trace log and clear all events.

Jan 28, 2009 | HP Compaq ProLiant ML110 G4 Server

Not finding what you are looking for?
Compaq ProLiant 1600 (315570-001) Server Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Compaq Computer Servers Experts


Level 2 Expert

78 Answers


Level 2 Expert

146 Answers


Level 3 Expert

7983 Answers

Are you a Compaq Computer Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides