I need to know, how do you use speed dial ? - Android LG Optimus Dynamic II LG39C Smartphone fo

If you have set up your numbers with speed dial, make sure the speed dial option is set "ON". When you are ready to make a call, press and HOLD the speed dial number you are calling. I had the same problem and found the solution on another online forum.

Guessing that you already know about SYSTEM speed dials, then the 12 buttons on the right side of your phone are the PERSONAL speed dials. When you get dial tone on the intercom, you can dial "9" and the system will either give you a dial tone, or the highest line in the system. If that is not a working line, you need to fix that first (system program 400 assigns lines in service).

Once you have that, a PF button is programmed by pressing PROGRAM, the button, and dial 9 + your number dialed the same way as if you had pressed a CO button then STORE. You can keep pressing PF buttons and programming numbers. Then press PROGRAM or pick up the handset and drop it back down to end programming.

Carl

Would need to know the phone model, there should be a way to set previous called numbers to a digit speed dial 1-10 etc. If you have a smartphone, Iphone does speed dial as favorites which are set up in the call menu. Droids have a specific icon for speed dial.

Rylan

You will have to get into program mode for this. you will have to press this sequence of buttons. Hold*#*#1*2*3*. Password is default to 0000. Program number is 902 then press hold. Press Intercom button for Date and line 1 button for time. If you press Intercom #66 enter speed dial number 10-99 is station speed dial. If you press Intercom #66 and enter speed dial numbers 100-999 will be system speed dial. Hope this helps. I included a site below with program manuals.

http://www.wedophones.com/ToshibaManualsLead.htm

Not knowing the specific model of the phone system itself (the PBX cabinet in the telephone closet) I would guess you are using the "personal directory" and it only has 10 number memory and it goes from 0-9. The system directory will give you more mems.

My Mom had this same problem.   I found these instructions on Uniden's website (uniden.com) under the "Owner Manuel" section.


Here you go - good luck!








Using the Speed Dial Memory 
Storing Numbers in Speed Dial Memory 
Your cordless phone can store up to ten numbers (up to 20 digits each) in the speed dial 
memory. To store number in memory: 
1) When the phone is in standby, press [memory]. The talk/batt low LED flashes. 
2) Use the keypad to enter the phone number. 
 (To enter a 2-second pause between numbers, press [redial/ 
pause]. Each pause counts as a digit. ) 
3) Press [memory] again. 
4) Select the speed dial location where you would like to store the 
number ( [0] to [9] ). You will hear a confirmation tone indicating 
that the number has been stored. 
NOTE: 
• Storing a number to a speed dial location will 
overwrite the any previously stored number without 
warning. 
• When storing numbers into memory and the handset is idle (i.e., no key is 
pressed) for more than 0 seconds, it will beep rapidly, and then the phone 
will return to standby. 
Dialing a Stored Number 
1) When the phone is in standby, press [talk], and listen for a dial tone. 
2) Press [memory] and enter the speed dial entry ([0] – [9]) that has the stored number 
you want to dial. (If you enter a digit that does not contain a stored number, the 
handset will beep rapidly, and the phone will not dial.) 
Chain Dialing 
The speed dial memory is not limited to phone numbers. You can store any number (up 
to 20 digits) that you need to enter once your call connects. This is referred to as Chain 
Dialing. An example is a frequently refilled prescription number. Store your pharmacy 
phone number in one speed dial and your most frequently refilled prescription number 
as another speed dial. To use, once you ring your pharmacy's automated prescription 
line, simply press [memory] and the speed dial number where you stored your account 
number. 
Erasing a Stored Number from Memory 
1) With the phone in standby, press [memory] twice. 
2) Press the number of the speed dial entry. A tone indicates that the stored number is 
erased from memory. 

to programme speed dial just go to contact on your phone menu and select the conatct you want to speed dial and assign speed dialing number for the person or you type any number on your phone and press the harsh key like this (10#) and it will bring out the number assign to that spedd dial

If you have a newer Toshiba phone system you will press Intercom #66 to get into speed dial. Once you in speed dial numbers 10-99 will be station speed dials and 100-999 will be the system speed dials. I included a website with manuals below. Hope this helps.

http://www.wedophones.com/ToshibaManualsLead.htm

Redial, speed dial enter the code(60- 99) for system speed dial
(10- 49) for personal speed dial. enter the phone number or the number you want to program then press redial.

Canon left me on hold for 30 minutes then told me this wasn't their problem and I should call my dealer for service.  I'll try that now.  Nope - they didn't know either.
Eureka!  Lift the panel that covers the speed dial buttons and push the button labeled "data registration".  Using the arrow buttons find the speed dial info and figure it out from there.  Good luck!