I have a Zebra 170xiIII. The feed motor runs both forward and backward. Will be running fine and I have to pause and will start running backward. Have replaced motor and same thing. What's wrong?

Question 1

0helpful

1answer

Hey Jack, we currently have 3 Zebra s600's, 2 in use and 1 spare. I've recently added some zp550 printers on the 2 computers that have the s600's and screwed up the drivers for the s600s. I...

1. Reset the printer - to return the printer configuration to factory default values,pressFEED and PAUSE at the same time while turning the power On (l).
2. Download this Maintenance Manual for Zebra S600 and follow the troubleshooting steps from page # 66.(table 3-2) Printer stops, pause and paper/ribbon LEDs both on / Printer stops, pause LED on and paper/ribbon LED flashing.
3.Uninstall / Re-install the zebra printer driver .Use this revouninstaller to remove the driverClick here to download the driver for Zebra S600 .

Oct 14, 2011 • Zebra Stripe S600 Thermal Label Printer

0helpful

1answer

I am having trouble in printing.. I send the label to my Zebra 170XiIII plus and it out of specs... any help please??

Make sure you are using the correct driver 170xiIII plus, and make sure the dpi of the driver matches the print head resolution.203 or 300dpi.

Sep 09, 2011 • Zebra 170XiIIIPlus Thermal Label Printer

0helpful

2answers

My zebra printer is not printing anything on the label. I've attached other zebra printers and it works normally, so I don't think it's an issue with the network. I've changed out the ribbon a couple...

Will it print anything at all? Or it is not printing from the computer? Power it off and press the cancel key while powering on and see if it will print a configuration label. Be more specific in relating your problem and we can be more help.

Jan 10, 2011 • Zebra 170XiIII Label Printer

0helpful

1answer

Have a Zebra 170XiIII Plus that goes straight to Pause when powered up, and no amount of resetting turns Pause off. LED display shows "Printer Ready" but no other information. Can't get to Setup...

press PAUSE and CANCEL to reset the printer. turn off and on again.

Nov 05, 2010 • Zebra 170XiIIIPlus Thermal Label Printer

0helpful

1answer

Have a Zebra 105SE that prints the FEED test just fine, but will not print the PAUSE test nor will it print a bar code label from the computer. The FEED test prints vertical bar codes while the PAUSE test...

Check to see if the pause light is on also. Make sure you are using the correct printer driver. (105se)
Try in ZPL and then try in ZPLII.
Check Delimiter character 2CH
Check Format prefix 5EH
Check Control prefix 7EH

Aug 24, 2010 • Zebra 105Se Thermal Printer

0helpful

2answers

Hello, Our company is using a Zebra 170XiIII plus printer and having a trouble with this machine. Every time when we are sending a print job to the printer there is always an single blank label fed through...

I believe you should check the website and download the manual and go over. I think you will find it useful.http://www.zebra.com/id/zebra/na/en/index/products/printers/high_performance/170xiiiiplus.html

Aug 05, 2010 • Zebra 170XiIIIPlus Thermal Label Printer

1helpful

1answer

Zebra Z4M only feeds a small portion of the label.

You should try a factory reset. Power off the printer. Hold the "pause" and "feed" buttons down while powering up. Allthe lights will blink and when they stop blinking, release the "pause" and "feed" buttons. This will factory reset the printer.

Apr 24, 2009 • Zebra Z4M Printer

0helpful

1answer

Zebra S500 not sensing media

download the driver www.seagullscientific.com
recalibrate media, if necesseray Reset to Factory defult.

Apr 02, 2009 • Zebra Stripe S600 Thermal Label Printer

2helpful

1answer

Zebra S300 printer pauses without printing additional copies

I Use driver from Nice Labels
http://www.nicelabel.com/downloads/nicedrivers/zebra seems to work fine

Dec 05, 2008 • Zebra Stripe S300 Thermal Label Printer

0helpful

1answer

Hoover Elite motor runs when moving backwards but not forward

Are you sure its not just your belt on the beater of head slipping and needs to be replaced?

Oct 18, 2008 • Hoover Elite Rewind Bagless Upright...

Question 2

Nick

Zebra Expert 124 Answers
Posted on Apr 03, 2015

Nick

Zebra Expert

Joined: Dec 21, 2011

Answers

124

Questions

1

Helped

43754

Points

534

The DC power supply drives that motor and may start running it backwards when it begins to fail. The motor normally makes more noise than usual in both directions when it starts to fail like this.

Google "43470-002 power supply, Xi III +" and you will be able to purchase the part.