Does the pit go pointy end up or down in water

Pointed end goes up and the end with the little "button" in the middle is the part that you put in water. Angle your toothpicks up a bit so the pit will set further down in the glass. Put in a sunny window and WAIT!!! Some people change the water frequently, others don't change it at all. I change mine every couple weeks....which is a happy medium. They will start to crack open (that's a good sign) but it will probably be a couple months before you get roots, and another month or two until you get enough roots to plant in soil. Roots are very fragile, so be careful. Hope this helps.

the pointy end is called the horn

No tools necessary. It's inside the pointy end of this inverter. Turn that metal sprocket right at the pointy end counter-clockwise until it releases. The nib/sprocket releases and the fuse slides out with them.

hi my pit bike bogs when i wash it

if the router is new, the password will be in the manual. If you are absolutely sure you dont remember, then get a paperclip, extend the pointy end by bending out. disconnect router power. push pointy end into the hole in the back of the router that is marked reset and hold it. Reconnect power while holding the reset down for a few seconds and then release. This should have reset your router. be clear that your router may be exposed or open to outside traffic as a result and will need to be resecured. password will likely be blank but some reset to something specific...see manual. good luck!

Why does it matter.?
If you plant it upside down, the stem will still find it's own way to the top.!

(it's the pointy end)

After the Goomba gets enlarged, stomp on the ?-Switch in the pit to make some
platforms appear to allow Mario to jump high enough to get above the Giant
Goomba, delivering a Ground Pound attack to hurt the monster. Keep at the
attacks from above, landing three total hits to take it down, ending the tour
of the poisonous waters of World Four!

the sump pump shold not be run into the sanitary sewer, but if your floor drain is hooked to a sump pump pit and it doesn';t pump the water before it gets to the drain tile it could come up in the drain,, to solve the problem get a pump that the float is lower in the pit,, suggestion zoeller cast iron submersable pump cost about 100 less the install price, great low profile pump, it keeps less waterin the sump pump pit so there is less mosture

Someone else had this problem and posted the solution online. I found it while planning to reupholster the drivers seat on my Olds Alero. Hope this helps, i've cut and pasted from wikianswers.... I had the same problem, hence my stumbling across this question this afternoon. i just spent a very frustrating hour working it out! first, to get an idea of how the black clips sit, place them in the rectangular gaps on either side at the front of the seat. the plastic clips sit in the rectangular hole, with the pointy ends facing up. the short one at the front. the short pointy end clips around the front edge of the rectangular hole. the longer pointy end that is now towards the rear of the car is meant to clip onto the wire that sticks out at the front of the seat. there is one on either side of the seat so it is easy to see them line up roughly. the pointy end doesnt clip around the u shaped bit that sticks out, but the striaght bit just behind that. now, if you can understand what i meant. it is time to install. take the plastic clip out of the rectangular hole. clip the long pointy end around the wire on the seat. lower it carefully into place. this is what i found the tricky bit. you can't see, so i lined it up by feel, and lowered it very carefully. then....... after trying many times to put in in place, a finally forced it in with brute stregnth and determination. you have to force it down towards the back of the car to make the clip latch into the rectangular hole. it took me ages to work out the frist one, then the second side only took a minute as i knew what to do. hope this was understandable and will help.

if you mean that water is coming out via the drawer that you put the powder then:

The powder has become solid in the drawer and blocked off the pipe leading to the drum.

What you need to do is to get boiling water and pour it into the detergant and using the pointy end of a wooden spoon break the sludge free in the pipe and the detergant draw.

Please leave feedback