Question about Fender Hot Rod Deluxe Guitar Combo Amplifier

1 Answer

How do I find Fender amplifires

Fender Marshall peavey korg sun

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,140 Answers

Http://intl.fender.com/en-CA/support/ Here is a link that will help you.

Posted on Feb 14, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How old is my peavey t-60 number00763401


It was Manufactured between 1981 - 1982
So it's about 33-34 years old...

Feb 28, 2015 | Marshall Mg100dfx 100-Watt Combo Guitar...

1 Answer

Can i find out the age of my eko guitar from the serial number


Unfortunatly, once you get past the well known Fender/Gibson/Gretch brands, info gets harder to come by.o can try contacting Eko directly in Italy. Here's a link
Numark Marshall Dunlop Korg PRS Akai Sonor EkoMusicGroup distributore di...
Or you can date the guitar off the codes on the pots. Here's some info on that-
Vintage Guitars Info dating vintage guitars amps by date source code

Feb 21, 2015 | Music

1 Answer

How do you connect a peavey 6505+ amp to a marshall 1960a cabinet?


On the back of your 6505 there are two jacks that are labeled speaker outputs. For mono function, use either one of those outputs and run a SPEAKER cable from your amp to one of the input jacks of your 1960a cabinet. I assume it is a 4X12 cabinet. Either input will work. Make sure you match the ohm selector on your 6505 (right next to the output jack, 4/8/or 16 ohms) to the ohm rating on your 1960 cabinet. It is likely labeled on the plate that houses the input jacks. You should be good to go. NOTE: Never turn your amp on unless it is hooked up to a speaker cabinet and never use instrument cable to hook your amp to your speaker cabinet. Bad for a nice tube amp like yours.
Rock on and hope it helps.

Dec 02, 2013 | Peavey Music

1 Answer

MARSHALL FOOTSWITCH FOR DSL100 TROUBLES


Does your M foot switch work on the Fender? If you know how to use a multimeter you could check continuity by putting meter leads on plug of M foot switch(1 on tip, 1 on sleeve ) You should see a change in the multi meter when you depress switch. If so switch is good. Another easy test is with cap off a spare 1/4 plug -plug it in to foot switch jack.put a alligator or some such metal clip or wire and join(called short or shorting) the two inputs . If connecting and unconnecting results in switching then the foot switch is suspect. One fairly common thing is that foot switch and input jack are often sautered straight to a circuit board to save $ on production cost. Used to be all point to point where a wire was attached to 1/4" input and then wire went to circuit board or tubes. The wire has give, but not so with direct wiring to board. So the nut holding the 1/4" amp input gets loose(doesn't have to be loose for the following to happen) and a pull on the chord causes a break in the soldier and thus a break in the sound chain. Sometimes it will work intermittingly by putting a little pressure left, right, up or down on the plugged in plug. If so, it's the input jacks connection to the amp. If not it still could be that because putting pressure on plug may not be sufficient to affect a temporary reconnection. Since switch(the new one you made)works on Fender, but not Marshall I suspect the jack or foot switch circuitry past the input jack. If using some of the above the above tests leads you that direction,remove housing(unplug a/c power 1st ) inspect jack,wiggle it slightly see or feel a break then resodier from back side. You should be able to use the soldier already present without adding extra.

Sep 27, 2017 | Music

3 Answers

How To Use The effect Loop?


The effect loop is to use exteernal effect module... It is NOT to use guitar pedals !!!! The signals are line levels, NOT guitar type levels. An example of a device might be an Alesis Quadraverb. You take the effect send jack and run it into the inout of the effects module and the output of the effects module into the effects return jack. Many try to use guitar pedals and massive distortion results because levels are too high for the pedals.

May 12, 2011 | Peavey 6505+ 112 Combo Amp Combo

1 Answer

Hi, I would to say thanks a lots to let put some words on yours email box. It's just regarding about how to set up a live band gigs @ outdoor stage in to mixer system. In a mixer setting, i wana know how...


You will need at least a 24 channel mixer to give you spare channels. You also need an active crossover and a snake. The advice you need is too much to include here so I am including some links:http://mixonline.com/live/FixIts/, http://en.wikipedia.org/wiki/Live_sound_mixing, http://mixinglivesound.com/blog/tag/outdoor-concerts/,http://mixinglivesound.com/blog/, and http://www.scribd.com/doc/11435651/Beginners-Guide-to-Mixing-Sound. You may need more monitors than you are planning on and you might consider in ear monitoring.

Aug 22, 2010 | Music

1 Answer

I am trying to source a copy of the user manual for a Marshall MG10CD amplifier. Can you help?


MOST of these small amps are so SIMILAR to the competitors that you can get the users manual for one and use it for another. They are not as the saying goes, "rocket science".

That being said, try for instance the Fender Frontman manual. Here is a site for download:

http://www.manualnguide.com/download/manual-guide/fender-frontman-15g15r-users-manual.html

You will find that even the scematic diagrams are quite similar between the brands. Let's face it, they can't re-engineer much as there is little profit.

MOST of these amps use one of the TDA family of chip audio power amps.

Nov 14, 2009 | Marshall MG10CD 10 Watt Combo Amplifier

Not finding what you are looking for?
Fender Hot Rod Deluxe Guitar Combo Amplifier  Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fender Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

rjivaro

Level 2 Expert

158 Answers

Marvin
Marvin

Level 3 Expert

85020 Answers

Are you a Fender Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...