Question about Garden

1 Answer

How do i remove the impeller from mycraftsman 1350 series 27" snowblower

I have owners manual that shows parts list but not instructions on how to remove impeller.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 84 Answers

Before I begin, this is a fairly involved process so if you dont have some mechanical experience you may want to pass it off.
First you have to split the snow blower so remove the bolts on the side of the case just behind the auger case.
how do i remove the impeller from mycraftsman 1350 - 25320447-e0sfnxd0aemnkmi0xvhhiizh-5-0.jpg

The three bolts just to the right of the tire must come off. Then the case will split apart. Stand the engine section against a table or something.
Tip the auger section up on its end so the pulley is facing up. you must remove the pulley by loosening the set screw or bolt on the shaft. This can be very difficult due to rust.
25320447-e0sfnxd0aemnkmi0xvhhiizh-5-1.gif

After you get the pulley off you will need to remove the auger assembly from the casing. You will first remove the bolts/nuts that hold the ends of the auger shaft to the side of the case. When those are off you will pull the auger shaft/gear case assembly out of the case. It will look something like this...
how do i remove the impeller from mycraftsman 1350 - 25320447-e0sfnxd0aemnkmi0xvhhiizh-5-3.jpgt/uploads/images/25320447-e0sfnxd0aemnkmi0xvhhiizh-5-3.jpg" alt="25320447-e0sfnxd0aemnkmi0xvhhiizh-5-3.jpg" class="h_mi" />

Once that is out, you will be able to get to the impeller bolts or pins. If you have bolts simply remove the bolts and slide the impeller off the shaft. Again, this may be difficult due to rust and/or wearing of the shaft under the impeller. If you have pins, the pins will have to be pushed through with a hammer and drift pin smaller than the pins themselves. Then you can purchase new how do i remove the impeller from mycraftsman 1350 - 25320447-e0sfnxd0aemnkmi0xvhhiizh-5-6.jpgardware store.

25320447-e0sfnxd0aemnkmi0xvhhiizh-5-6.jpg

Once you replace the pins, put the machine back together.

Posted on Dec 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need a manual and parts book for a treadle sewing machine. Serial number B481745. I believe model is 27.


go google and type in---workshop manual for singer sewing machine model 27--
the beauty of singer is that there were few changes made in the treadle series so any book around that age would be helpful

Sep 10, 2016 | Singer Sewing Machines

1 Answer

Cant find hp psc 1350 on list of hp printers


HP "series" numbering can be somewhat confusing, but Windows 7 does have the correct driver for your printer.
For the HP PSC 1350, you will need to use the 1300 series driver.

The 1310 series driver is for models numbered 131x (e.g., 1315, 1318).

Jan 25, 2013 | HP PSC 1350 All-In-One Thermal Printer

1 Answer

Swisher 27" snowblower front impellers turn free


Hi Craig,

Most snowblowers incorporate "shear pins" between the motor and auger. A shear pin looks similar to a nut and bolt or pin that couples the drive to the auger - but it designed to break or shear off to prevent damage to the auger or motor in the event of a jam or overload. They look like these:

12_21_2012_2_20_37_am.jpg

12_21_2012_2_20_57_am.jpg

Only the shear pin recommended for your particular brand and model snowblower should be used. Under no circumstances should a regular bolt or other steel pin be used instead of a shear pin. Check your manual or consult with Swisher to determine the correct shear pin for your snow blower.

I hope this helps & good luck!

Dec 21, 2012 | Garden

1 Answer

Purchased a FD-27W Nesco Dehydrator at Thrift Store. Do you have an instruction manual I could download to my computer?


The Nesco website has Owner's Manual Download's for their products. However, the FD-27 Model is not listed. So, I called their Customer Service Department and they said that the FD-35 series is comparable to the FD-27 model. Here's the link:http://www.nesco.com/customer_support/owners_manual_download/english/

Sep 21, 2011 | Nesco American Harvest Snackmaster Food...

1 Answer

CRAFTSMAN®/MD Electric Snowblower owner's


If this is a Craftsman product then you should be able to enter the model number here and get one.. The manual tab will be on the right after they find it for you. A lot of repair information is not available in manuals, but Sears manuals are known to have parts schematic breakdown lists and diagrams, plus you can purchase from the online parts breakdown lists.
http://www.searspartsdirect.com/partsdirect/index.action?psid=26132896&sid=PSx20071217x00001d&OVMTC=b&OVKEY=sears%20part%20direct&creative=726752&adcid=1987828

Jan 16, 2011 | Craftsman Garden

1 Answer

Ariens snowblower impeller not throwing snow


Sounds like you have a broken or partially broken shear pin in the auger.Check along the auger[machine off]and see if there is what looks like a bolt anywhere along the auger shaft.If there is [and there will be] remove and inspect it and you will see why the auger is not working.Next time,never clean out a chute or auger while the engine is running,people loose limbs this way.

Feb 13, 2010 | Ariens 34 In. Zoom Series Riding Mower

Not finding what you are looking for?
Garden Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2475 Answers

john h

Level 3 Expert

11034 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...