Question about Televison & Video

1 Answer

Know what channel the TV is tuned to. There is no indication on the screen. This is a saber

Using the channel up &down button on the right side of the set

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Televison & ... Master
  • 74,185 Answers

Press the "Display" button at its remote control. The channel tuned in will be displayed for just 5 seconds; and will vanish automatically. You should have its remote control; of course. You can't get this display by its panel buttons by anyway..
If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one.
To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have.
Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops.

Posted on Dec 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Button to scan in channels


The CT-90326 remote was included with several Toshiba televisions, including the 42HL800A. You can't directly scan for channels with a single button on the remote. First make sure that the TV is set to the TV input. (Use the Input button on the remote (top left) or the TV (lowest button on the left side as you face the screen).) Next press Menu (the second lowest button on the TV or the button at the lower left of the Left arrow button). Use the Left or Right arrows to select Setup (with the gear icon) and press OK. Use the Up/Down arrows to select Auto-Tuning and press OK. Use the Up/Down arrows to reach the line to select the type of channels to search for a signal. Then use the Left/Right arrows to select Digital channels, Analog channels or both. Go down another line to set the bandwidth of your broadcasts. Again use the Left/Right arrows to select the correct one. Go down one more line to Start Scan and press OK.

These details are in the manual for your TV. The manual for the 42HL800A is available from Toshiba's product support download page: http://www.mytoshiba.com.au/support/televisions/led-backlit-tv/hl800a/42hl800a/download . The direct link to the manual is http://www.mytoshiba.com.au/file/download/resource/file/19610/toshiba_32av80032%2040lv80026%2032el80032%2042hl800_om%20(au).pdf .
I hope this helps.

Cindy Wells

Oct 02, 2016 | Toshiba CT-90326 Remote Control

1 Answer

We dont have a manual and we dont know how to change the channel or set the time


To set the clock on the unit, have the TV connected to power but not on. Then press and hold Mem/Clck Adj on the TV (it's the third button from the right in the top row of controls). Use the adjacent Tune/Clk (up/down arrows) to set the clock for 12 or 24 hour time. Then press Mem/Clk Adj again to adjust the hour with the up/down arrows. Press Mem/Clk Adj again and set the minutes. Press Mem/Clk Adj to save the time. The original remote also has these buttons. Mem/Clk Adj is also labeled Set and is the furthest right button on the second to bottom row of the remote. The Tune/Clk buttons are the DN and UP buttons on the left of this row.

Use the Tune/Clk arrows to change the radio channels after pressing the radio button (second from the right on the bottom row). When you press the TV button (first on the right of the bottom row) to watch TV, then you need to use the Channel up/down arrows at the top and bottom of the ring control on the far right of the TV or the Channel + and Channel - buttons on the remote. On the remote, the Channel + button is below the timer button which is below 9 in the keypad section. Enter is below the Channel + button and Channel - is below Enter. Make sure that the TV is in the correct mode for your signal (ATSC for OTA and NTSC for analog cable) by pressing the TV mode button. If you are using a set top box, you will need to change the channels at the box.

Press the TV Menu button and then go down the list to Time to set the time zone for the TV. Press Enter to save the setting. Use the TV Scan button to get a list of available channels before trying to change channels.

The manual for the GPX KL868S is available from GPX at the product page: http://www.gpx.com/store/p/287-KL858S.aspx . The direct link to the English version of the manual is: http://www.gpx.com/owners_manuals/KL858S-IB.pdf .

I hope this helps.

Cindy Wells

Aug 22, 2011 | GPX KL858S 8.1 in. Under Cabinet TV

1 Answer

How do I tune a sony trintron without a remote


Hello
You can autotune your Sony TV without a remote control. Fist connect it to an external antenna or cable whatever may be, to its antenna socket at the back side.

After you have finished connecting your TV, you can use Auto Program to set up your

channels. During Auto Program, the TV will automatically search for available channels and
program receivable channels.

[1] Press POWER button on the TV to turn it on. The Initial Setup screen appears.

[2] Press CH+ button on the remote control or on the TV front panel to start Auto Program, or press CH-- button to exit.

The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.

To perform Auto Program again

1 Press"MENU" button on the front panel of your TV.
2 Press "RIGHT ARROW button to highlight Channel Menu.
2 Press DOWN ARROW BUTTON to highlight CABLE or ANTENNA AND PRESS [+} to select.

4 Press UP arrow or DOWN arrow to highlight On or Off according to how you connected your TV. Press [+] to select.

4 Press F or f to highlight On or Off according to how you connected your TV. Press to
select
5 Press DOWN arrow button to highlight Auto Program. Press [+]to search for channels
6 After Auto Program finishes, press MENU button to exit.
OK



Dec 18, 2010 | Sony FD Trinitron WEGA KV-24FS120 24" TV

1 Answer

We can't get any of the channels don't know where to start from menu area


Hello

You just do autotune to receive all channels. In this mode TV will tune through the entire channel band automatically, and finally will stop tuneing, and will show the first channel receved. You must be patient for these time. about two or three minutes, without disturbing is process. The tuning process follows.

Auto Tuner Setup

In Auto Tuner Setup, the TV automatically scans

t h rough all available channels, memorizing the active

ones and skipping over blank ones or channels with

weak signals. This means when you scan (using the

CH A N N E L +/- b u t t o n s ) you will receive only clear,
active channels
P ress the ME N U b u t t o n
Press UP or DOWN buttonTo AUTO TUNER SETUP
Press Right or Left button to operate
Press Vol+ or Vol (--) to choose CABLE or AIR
Press UP or DOWN button to move to START
Press Right or Left Button to start Auto Tuner Setup

Tv will show "NOW PROGAMMING" display.
Programming will take approximately 1 to 2 minutes.
After all it will show
PROGRAMMING OVER

Some cable systems experience interference from radio frequencies on cable Channel 95. You may delete this channel from
your scan by removing the "X" next to it on the Channel Summary screen.

Nov 29, 2010 | JVC AV-27120 27" TV

3 Answers

How do you tune in a alba tv with no remote control


There is no way to tune it, the menus that you need to bring up can only be accessed with the menu buttons on the remote

Feb 28, 2010 | Televison & Video

1 Answer

No user manual for CE28DN9-B. Bought TVonics


HELLO

Follow these instructions:

Select a spare channel on your TV say 6 on your remote.

Press MENU.

Scroll down and select PRESET.

Using RIGHT button of F/OK/ENTER press it and this will go to TUNING.

Press RIGHT button again which will let you go to SEMI or AUTO tuning (for your purpose select "SEMI").

Scroll DOWN to highlight the actual UHF channel number or CH:C21 as it may appear on the screen.

Press the RIGHT button again yourself manually and you will see the channel number change anywhere from 21 to 69 until you come to your freeview box's RF channel output.

When you have done that scroll down to Memory and you'll see a box beside it. Press the RIGHT button and a tick will appear in the box.

You have stored your Freeview box RF channel on your TV.

Press MENU button THREE time to come out of the MENU setting.

Use this procedure again if you wish to change the RF channel on your TVONICS box.

GOOD LUCK (:-)

Oct 03, 2009 | Televison & Video

3 Answers

Technika tv lcd 19-907 tuning in to sky in bedroom.


Hi i had the same problem but i have sorted mine now. What i was doing wrong was i wasnt tuning in the analoge channels only the freeview digital ones. To do this you need to first turn your tv on. Then press the "source" button, this will bring up a little menu at the top left hand side. When this menu comes up press the "Programme +" button (the one that you use for changing channels near the volume button) press this until you get up to "TV", when T.V is highlighted just wait 3 secs and it will switch over. You will probably get a blue screen with a no signal message (you are now on analogue) when you get this blue screen press the "tune" button. It will automatically start tuning in all of your channels, at first they will be fuzzy but as it works they will become clearer. Your sky channel will also be tuned in. When mine tuned in it didnt tune them in on the right numbers though, bbc2 was on number 1 etc. If you ever need to use a playstation or something it goes into the scart connection at the side of the t.v and you need to press "source" and go up to "scart". To get back onto the digital channels just press "dtv/dvd".
hope i helped!

Dec 14, 2008 | Televison & Video

1 Answer

Mitsubishi diva cant tune in


well .... no online user manuals for thoseTVs
you will need to use a digital seck top box and use that units remote to tune the TV

if there are any (needs a user manaual)
use the buttons on the TV lower casing
to tune up


none of the all in ones remote buttons work for all TVs functions
you are lucky if it turns on and off
and changes channel

index-bwbjq1d2inqbxh534mfqkm1n-3-0_0.jpg

Apr 29, 2017 | Mitsubishi VS-45609 TV

1 Answer

Sony KV14T1U tuning


Press and hold for a few Seconds the 2nd Button from the left on the front of the TV. The auto tune menu will appear on the bottom right of the screen. Wait until it disappears and then check the channels by using the buttons on the remote.

May 20, 2008 | Televison & Video

1 Answer

Toshiba D-VR650KU can't "see" digital channels


On the Notification screen with Cable highlighted I found that left clicking on Cable gave a drop down menu with TV on it for selection. The manual says that while Cable is highlighted, use the up or down arrows to get TV to be an option and then select it and Yes and enter. Hope this helps. I have other problems with my monitor on Line Out, the screen oftens turns blue indicating low or no video using Line 1 or 2 inputs.

Feb 21, 2008 | Toshiba D-VR650

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74185 Answers

Cindy Wells

Level 3 Expert

5123 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...