Question about Mitsubishi Televison & Video

1 Answer

How do i install a new ballast for projection lamp ballast in mitsubishi model wd 52327

I replaced lamp twice with new, TV picture does not turn on. I need info on how to install a new ballast.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 29 Answers

Not sure if this is your TV for it don't specify a model of TV, only stating a V41 Ballast

https://docs.sony.com/release/KP53S75.PDF

This video specifies nothing but goes more in depth w/audio

https://www.youtube.com/watch?v=5frOnh58Z6M

TV's shown are different but the ballast part is the same (location and cables).

Posted on Dec 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have to change the lamp on my mitsubishi dlp tv. where is the lamp located?


Here is a link to the owners manual for lamp cartridge replacement. Specifically go to page 65 for instructions. Good Luck : )

http://support.mitsubishi-tv.com/files/oguide/WD-52327.pdf

Jul 26, 2011 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

I have replaced the lamp on my Mitsubishi WD52327 with a non oem version and the tv started clicking can you tell me what that maybe?


The tv board that call the Ballast board it is also dead too.This ballast board only job are to ignite the tv projection lamp only.

Jun 14, 2011 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

Mitsubishi 52'' TV Model WD52525


U restart the tv,u hear alots of clicking?That mean the Ballast is dead or have problems,that why ur picture lamp not sustaning the picture.Replacing the Ballast might or will sustance the picture.

May 18, 2010 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Recently my wd-52327 said it needed new bulb(steady orange light). i had replaced the bulb 7 months earlier and didn't want to see the light so i reset the lamp timer. well the bulb blew the next time i...


If you have a voltage meter you can pull the bulb out and check for continuity by placing the probes on the power plugs of the bulb. If you have continuity the bulb should be good, and it may be the lamp ballast.

Nov 21, 2009 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

Mitsubushi tv model # 52327 ballast replacement


The ballast for the lamp too should be replaced along with the lamp. If you wish to get some details; visit the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

Mar 13, 2017 | Mitsubishi WD-62525 62" Rear Projection...

2 Answers

How to clean Mitsubishi TV WD-52327 fliter


Remove the 2 screws in the access panel on the left rear side of the tv. You will see the filter behind it. Rinse the filter in warm water until clean. Lay it flat on a paper towel and fold the other half of the paper towel over it. Press gently on the towel to soak up most of the water, and install it in the tv.

Oct 10, 2009 | Mitsubishi WD-52327 52" Rear Projection...

1 Answer

Buzzing noise from Mitsubishi DLP WD-52327 after replacing bulb


Did your replace lamp come on the screen or did you lose picture? Just because the LED indicator suggest replace lamp it doesn't mean it needs it. If your pix was dull or loss of brightness then replace it, if not then just reset your lamp timer, check your owners manual for instructions.

Feb 14, 2009 | Mitsubishi WD-52327 52" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1208 Answers

The Knight
The Knight

Level 3 Expert

73591 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...