Question about Tools & Hardware - Others

1 Answer

I have a stanley 80493 belt sander 3 x 21 model

I have a stanley 80493 belt sander 3 x 21 model 04 I need to get a belt for it, where can I find one ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

You can contact Sears they will find the part for you or go on Stanley tool site and e m ail them the part # or u can go to ur local hardware or mini bike shop they will have various size belts

Posted on Dec 11, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I purchase drive belt for Stanley belt sander Model 0.4 #80493?


lowes also look up sanding belts .com some are 40 percent off the cost

Apr 28, 2017 | Sander Tools & Hardware - Others

1 Answer

I need a drive belt for a Stanley belt sander


Unless there is a model that I have never seen, the sandpaper is the drive belt on belt sanders.

Jul 04, 2014 | Hand Tools

1 Answer

Belt slips on Stanley belt sander model H-31A


On most belt sanders the back wheel or the idle wheel has an adjustment on it, loosen the bolt that goes through and slide back. Some have an adjustment screw that will pull or push the idle wheel. That should be on the inside of the wheel.

Mar 05, 2014 | Hand Tools

1 Answer

Need motor brushes for a stanley heavy duty 4'x24' belt sander. type: 497, model A, amps: hi-8.5, lo-7.0, volts 115, serial # 457244. thanks, tom


Hiya
I had the same problem, cannot find spares. I went to a local tool hire company and purchased two brushes (Part No. L41F10). You will need to shorten them by approx.1/4"", swap the springs and cut down the metal terminal to same shape as the original. A small 1/2 round file, junior hacksaw and about 15 minutes should get you going.
I am looking for a trigger (on/off) switch to suit my sander, if anyone can help I would appreciate it. Only other option seems to fit an inline switch to supply cable.

Jun 15, 2011 | Garden

1 Answer

We have a really old Stanley 3" Belt Sander that has a worn electrical cord. We want to replace the cord; however, we cannnot get to sander open in order to install a new cord. We have all the...


use a screwdriver (rubber handled) to smack around the tool to losten it. you hill find that the seam will start to open.. then carefully pry it open with a flat blade.. if it is hard in one area look close to see that you didn't miss a screw ... jay

Jun 06, 2011 | Stanley Tools & Hardware - Others

1 Answer

I have a Porter Cable Model 371 2.5" X 14" Belt Sander. I broke a belt, when I did it jammed and also broke a rubber sleeve that covers the Drive Wheel. I have yet to find this rubber sleeve in any part...


Unfortunatly that sleeve is not available, you will need to purchase a whole new drive wheel. The Drive wheel is $9.66 from DeWalt Service Net. Porter Cable, Delta & DeWalt are all owned by Stanley Black & Decker, you can contact DeWalt Factory Service for all parts. 1-800-4-DeWalt You can order the parts on-line, over the phone or though a local service center. The website is www.dewaltservicenet.com Below is the parts diagram for your sander. The part number for the drive wheel is A16439
http://www.dewaltservicenet.com/Products/DocumentView.aspx?productid=65594&typeId=15450&documentId=34604

Oct 10, 2010 | Porter Cable 371K Factory Reconditioned...

1 Answer

Need a manual for a Craftsman belt & circular sander


I found a PDF file on Sears.com website for the original manual for my belt / circular sander.

Oct 21, 2009 | Tools & Hardware - Others

1 Answer

Parts


I have the same sander, and cannot get parts anymore, so I carefully cut out a piece of sheet metal, and drilled holes, and put it on. so it might not say stanley, but who cares? I don't. and if it doesn't last as long, who cares. its more help than I got from stanley, who was bought out in 1973 from what I read.

Oct 18, 2009 | Stanley Hand Tools

1 Answer

HOW TO CHANGE THE BELT ON A BELT SANDER


There is a lever on the side of the unit, flip the lever and then slid the belt off.

Jun 13, 2009 | Makita 9404 4'' x 24'' Belt Sander

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

75824 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...