Question about Televison & Video

Open Question

I have a neco MK1 shutter remote control unit when i press the close button it opens it and when i press the open button it closes it.

I have found this so far !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!REMEMBER ONLY USE THIS AS A GUIDE AND IF COMPETANT TO CARRY OUT THE TASK.!!!!!!!!!!!!!!!!!!!!! !!!!!!!1THIS IS JUST FOR INFORMATION DONT MESS WITH ELECTRICS IT CAN LITERALLY KILL OR CATCH FIRE ETC!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! LED 1 = used for programming new remotes LED 2 = on when safe is connected to common LED 3 = on whilst open on JX3 is linked to commmon LED 4 = on whilst close on JX3 is linked to commmon LED 5 = unknown at moment DIPs 1 = enable open function on jx3 DIPs 2 = enable close function on jx3 DIPs 3 = dead man open on jx3 DIPs 4 = dead man close on jx3 AN 1 = press once will flash LED1 during the flashing period press a button on remote until LED1 changes pattern Keep pressed for 5-10 seconds to wipe all remotes SW 1 = adjust the time open on jx2 is activated for...not applicable when using the dead man ioption on jx3 but still timed on remote SW 2 = adjust the time close on jx2 is activated for...not applicable when using the dead man ioption on jx3 but still timed on remote JX1 pinout (please note this is how it is labeled and it is up to you to verify its the exact same as mine) . . . . . . E [ E N L ] {L N } a [ a e i ] {i e } r [ r U v ] {v u } t [ t t e ] {e t } h [ h r ] { r } [ ] { } [ MAINS in] {Light} JX2 pinout (please note this is how it is labeled and it is up to you to verify its the exact same as mine) . . . . . [C O C] {+ - } [o p l] { } [m e o] { } [ n s] { } [ e] { } [ ] { } [Motor] {24V DC} JX3 pinout (please note this is how it is labeled and it is up to you to verify its the exact same as mine) . . . . . C S O C S o a p l t m f e o o e n s p e JX1 Mains in = 240v power from mains JX1 Light = activates 240v mains out to power a light (check the rating of fuse) JX2 motor = wiring to motor JX2 24V DC= aways on outputting 24v DC to power sensor for JX3 SAFE/STOP JX3 = common to activate the SAFE/OPEN/CLOSE/STOP if no sensors are connected then you still have to wire the common to safe and common to stop !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!REMEMBER ONLY USE THIS AS A GUIDE AND IF COMPETANT TO CARRY OUT THE TASK.!!!!!!!!!!!!!!!!!!!!! !!!!!!!1THIS IS JUST FOR INFORMATION DONT MESS WITH ELECTRICS IT CAN LITERALLY KILL OR CATCH FIRE ETC!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Garage Door Openenr Motor Buzz

Look at your manuel find the page that shows the limit access switch. (Unplug your opener.) It isn't really a switch, but the three white plastic screw like parts. The center has a brown wire connected to it, which has a metal piece that is as wide as all three white screws. The outside screws are your limit access stop guides, one for the up control stop guide and the other for the down control stop guide. If the center screw with the metal part gets caught behind on of the stop guides the motor will not engage. Gently move metal piece from behind the stop guide.

Posted on Nov 10, 2008

ktkodama
  • 37 Answers

SOURCE: Remote does not open garage door

It sounds like the wall button has the lock feature engauged.

Is there a small green LED flashing inside the wall button?
Push and hold the lock button for about two seconds and the LED should stop flashing. This will unlock the garage door opener and your remotes should start working. You may have to reprogram your remotes and homelink again since you triedprograming in the lock mode.

Good luck.

Posted on Jan 20, 2009

  • 10865 Answers

SOURCE: i have a chamberlain 950-315cb

Here is the website which will provide you with all of the info you need on the chamberlain remote and door openers

http://www.liftmaster.com/consumerweb

Posted on May 19, 2009

  • 1 Answer

SOURCE: RAV311 WJ40930 US how to program the TV on the remote

It does not prompt you to enter your code, simply hold the 2 buttons for a few seconds, then enter the code you have. If successful, it will read remotesetup OK. Hope this helps and if you have any codes for techics cd players, let me know!

Posted on Dec 20, 2009

  • 1 Answer

SOURCE: TVTECH Universal Remote (3 Devices)

i got a universal remote it dont have my code in the book i have a durabrand tv do you have any i deal what the code is

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cannot get my SE32HY27-D led tv to eject the cd. It says press the open and close button but I did not find such a button


I think the displayed message refers to the remote control button. So there are a few buttons to control the DVD on your remote. As I don't have any image of the remote I must suposse some buttons have a second function when they are used to control the DVD. Please check all with care.

Jan 18, 2015 | Televison & Video

Tip

Digilogic DVDVCR2 Region Free Code Would you like your Digilogic DVDVCR2 to be...


Digilogic DVDVCR2 Region Free Code
3d9b18f.jpeg
Would you like your Digilogic DVDVCR2 to be region-free and play all DVDs? Here are the steps to make your Digilogic DVDVCR2 region free:

  1. Press the Standby button on your remote control to place the unit into Standby
  2. Press the Standby button on your remote control to turn on the unit
  3. Press the Open/Close button on your remote control to open the drive tray
  4. Press the Clear button on your remote control
  5. Press the 1 button on your remote control
  6. Press the 3 button on your remote control
  7. Press the 6 button on your remote control
  8. Press the 9 button on your remote control
  9. Press the 0 button on your remote control
  10. Press the Open/Close button on your remote control to close the drive tray
  11. Press the Standby button on your remote control to place the unit into Standby
  12. Press the Standby button on your remote control to turn on the unit
Your DVD / VCR combo is now region free.
__________________________

Is your Digilogic DVDVCR2 locked in SAFE mode? View my other Digilogic tip to unlock SAFE mode.

on Apr 07, 2010 | Televison & Video

1 Answer

Is there a Unlock code for bush btvd91216w


This is everything that I have:


Try this general bush unlock:

Press Open tray

Press 2, 8, 1, 2 and Enter to get to the manufacturers settings

Select the required region, by pressing Enter on 9 for multi region

Press Close tray

If that didn't work, try this:
Try this one:
1. Press the Open button on your remote control to open the drive tray
2. Press the 9 button on your remote control
3. Press the 7 button on your remote control
4. Press the 3 button on your remote control
5. Press the 5 button on your remote control
6. Using the on screen menu, highlight the region option
7. Press the Right button on your remote control
8. Using your remote control, select 1 for region 1, 2 for region 2, and so on, or 0 for multi-region playback
9. Press the Enter button on your remote control
10. Press the Open button on your remote control to close the drive tray


Then there is the following and good luck:
Bush 1000
  1. Open the tray
  2. Insert a disc with desired region code, but do not close the disc tray
  3. Press 0, 1, 2, 3, Play
Bush 1005 / 2004A / DVDAV7
  1. Press the OPEN/CLOSE on the remote
  2. Press 3, 3, 0, 8, 8
  3. Press the button for the desired region or 0 for multi-region
  4. Press OPEN/CLOSE
  5. The on-screen display will now indicate the currently selected region
Bush 2000
  1. Open the disc tray
  2. Insert RC-1 DVD, don't close the disc tray
  3. Press 0, 1, 2, 3
  4. Press PLAY
    To activate RC 2:
  1. Open the disc tray
  2. Insert RC-2 DVD, don't close the disc tray
  3. Press RETURN and PLAY
Bush 2002 / 2004
  1. Press OPEN
  2. Press 7, ENTER, 7
    A menu should appear (codefree=13)
    Method 2:
  1. Press OPEN
  2. Press 2, 0, 0, 1
Bush 2005 / 2008 / 2009
  1. Turn on the player
  2. Press OPEN/CLOSE
  3. Press ZOOM
  4. Press A/B
  5. Press Up, Left, Down, Right
    A note should be displayed.
  6. Turn it off
  7. Turn it on
Bush 2023 / 2024 / 2523
  1. Press OPEN
  2. Press 2, 8, 1, 2, Enter
  3. Set the country code to 13 and press Close
Bush 2028
    already region free
Bush 2039
  1. Press OPEN
  2. Press PROG
  3. Press ENTER three times
  4. Use UP/DOWN to select region
  5. Press STOP several times to set the region
Bush 2047
  1. Press OPEN, SETUP
  2. Go to "Preferences"
  3. Enter 2, 8, 1, 2
  4. Use UP/DOWN keys to select the region
  5. Press SETUP, OPEN
Bush DVD-102
  1. Press OPEN/CLOSE
  2. Press 2, 0, 0, 1
  3. Press ENTER
  4. Select RC (codefree=13). You can disable MacroVision, too.
  5. Press OPEN/CLOSE
Bush DVD-142TV
  1. Press DVD function on your TV set
  2. Press DVD Setup on the remote
  3. Press 1, 3, 6, 9
  4. Press Left three times
  5. Press RIGHT once
  6. Select VERSION
  7. Change the region code
Bush DVD-143TV
  1. Press DVD/TV, DVD
  2. Open the tray
  3. Press SETUP, Right, Left, Down, Up, Display
  4. Enter 0 (or 1-6 for other RC)
  5. Press Enter
    VCD/SVCD playback
  1. Press SETUP on remote
  2. Press Next, Prev, Next, Prev
    Ver should appear in the top right
  3. Change 3001 to 3000
  4. Change 5001 to 5000
Bush DVDAV11K
  1. Open the tray (be sure to be in stop mode)
  2. Press SETUP, Next, Prev, Next, Prev
  3. Select 255 for region free (use LEFT/RIGHT)
  4. Press SETUP
Bush DVDR3000
  1. The disc tray has to be empty
  2. Press TV/DVDR
  3. Press RETURN, DISPLAY
  4. Enter 8, 8, 8, 0
Bush DVHS1
  1. Press the DVD button on the remote
  2. Press OPEN
  3. Press 0, 5, 2, 0
  4. Press UP, DOWN, LEFT, RIGHT
  5. Change the region (0 = multi-region)
Bush DVRHS02
  1. Push SETUP button on the remote
  2. Select SYSTEM INFO on the menu
  3. Enter 1, 1, 0, 1
  4. It shows the current region code
  5. Push 0 on the remote for region free
Bush 2001 / 2020 / 2026 / 2029 / 2035XI / 2038 / 2042 / 5020 / BTV213DVD / DVR3000 / DVRS01 / PDVD0707 no known hacks

Jun 12, 2012 | Bush Televison & Video

2 Answers

How can I change the region on my Toshiba SD K860?


1. Power on the DVD player
2. Press the Open/close button on your remote control to open the drive tray and remove any disk
3. Press 2403960
4. Press 9 for multi-region playback. DO NOT Press Enter button on your remote control
5. You will see a 9 (region-free) on the TV (right corner)
6. Press the Open/close button on your remote control to close the drive tray
7. Power off the DVD player
8. Power on the DVD player and it is region free.

May 22, 2011 | Televison & Video

1 Answer

How to use the mc-dc2 how many buttons do i push to operate


There's only one button on the MC-DC2. Just plug it into the appropriate jack on the camera. You don't need to change any settings on the camera.
The button on the MC-DC2 now does exactly what the shutter release button on the camera does. The only exception is when the shutter speed is set to bulb. In this case the shutter remains open as long as the button is held down. There's a hold ring around the button on the remote; press the button and slide the ring in the direction of the arrow to hold the button down. Slide the ring in the other direction to close the shutter.

Mar 31, 2011 | Nikon MCDC2 Wired Remote Control for D90...

1 Answer

Is it possible to achieve a 20sec shutter release via remote control


With or without the remote control, in the M exposure mode you can select the bulb/time setting. Without the remote, this opens the shutter when you press the shutter release and holds it open while you keep the shutter release pressed. With the remote, this opens the shutter when you press the button on the remote and keeps it open until you press the button again. This allows you to keep the shutter open for up to 10 minutes.

Nov 29, 2010 | Nikon Coolpix 8800 Digital Camera

1 Answer

Hi, I would like to take a timed exposer, maybe for as long as five minutes......Thanks


In manual exposure mode, set the shutter speed to bulb. This is the next slower shutter speed past thirty seconds. The bulb setting will keep the shutter open as long as you keep the shutter button pressed.

It's easier if you have a remote control. With the ML-L3 wireless remote, you can press the button once to open the shutter and again to close it. Most wired remotes have a lock so you can lock the shutter open until you want to close it.

Nov 24, 2010 | Nikon D70s Digital Camera

1 Answer

Unlocking my DVD Player


Try this,it should work....Rod
To change the current region setting on this player
1. Press the Standby button on your remote control to place the unit into Standby
2. Press the Standby button on your remote control to turn on the unit
3. Press the Open/Close button on your remote control to open the drive tray
4. Press the Clear button on your remote control
5. Press the 1 button on your remote control
6. Press the 3 button on your remote control
7. Press the 6 button on your remote control
8. Press the 9 button on your remote control
9. Press the 0 button on your remote control
10. Press the Open/Close button on your remote control to close the drive tray
11. Press the Standby button on your remote control to place the unit into Standby
12. Press the Standby button on your remote control to turn on the unit

Jul 16, 2008 | Durabrand Televison & Video

1 Answer

DVD-RAM will not eject via "OPEN" tray command


Hey I just found out how to UNLOCK the tray
Power up the unit, wait for it to read the disc if one is inserted.
hold the stop button and the power button down together for 5 seconds
the display will show UNLOCKED
Open/close button should be restored

Apr 03, 2008 | Panasonic DMR-T2020 DVD Recorder

2 Answers

Durabrand LEDVD0701 dvd player


Taken from another site in case you still need to unlock it.

The Pacific hack works for this one!

Multi-Region Hacks for Pacific DVD-1001

To change the current region setting on this player
1. Press the Standby button on your remote control to place the unit into Standby
2. Press the Standby button on your remote control to turn on the unit
3. Press the Open/Close button on your remote control to open the drive tray
4. Press the Clear button on your remote control
5. Press the 1 button on your remote control
6. Press the 3 button on your remote control
7. Press the 6 button on your remote control
8. Press the 9 button on your remote control
9. Press the 0 button on your remote control
10. Press the Open/Close button on your remote control to close the drive tray
11. Press the Standby button on your remote control to place the unit into Standby
12. Press the Standby button on your remote control to turn on the unit

Oct 20, 2007 | Televison & Video

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

868 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73619 Answers

Cindy Wells

Level 3 Expert

5056 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...