Question about SATO CL408e Thermal Printer

1 Answer

How to calibrate a sato cl408e?

I wanna calibrate the printer manually and on the pc as well

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Expert
  • 82 Answers

Download the driver for your printer(free) from www.nicelabel.cl
That driver is the best in the world for those printers. In the Options tab, check for calibrate... button in the bottom.

If you want to go manual:
- Turn printer off
- Hold feed/Cal button
- Turn printer on while holding the feed button for 5 seconds aprox.
- Your calibration will start when you let go the feed button.

Posted on Mar 06, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

checkitright
  • 1362 Answers

SOURCE: SATO eSeries CL408e driver

here it is

 

 

http://www.satoworldwide.com/our_products/software.asp

Posted on Oct 22, 2007

SOURCE: printer problem

check baud rate on NIC card (pull out NIC), against COM settings on PC. they must match. 9600 usually works

Posted on Jan 14, 2008

  • 4 Answers

SOURCE: pare parts in India for SATO CL408e printer

you can contact sato represetive on 9422301045 to get help on stao printers

Posted on Jun 02, 2008

  • 52 Answers

SOURCE: my sato cl408e label printer misses printing on

recalibrate the stock.

Posted on Jan 27, 2010

  • 1768 Answers

SOURCE: my network can't detect the new sato cl408e we just purchased.

1.Log into router
2. Verify wireless router name( on the computer) >>> ( on/off)
3.Note router name you are connecting to.
4.. Check the laptop,desktop,printer do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address.
6.Note router name you are connecting to.
7. Move the device about 20ft away and try to log on to the internet.
This is for all routers to set up wirelessly.

Posted on Jun 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello my SATO CL408e can't install USB DRIVER (Win 7x64)


It won't auto install that driver you need to download the driver and install it manually.

This is assuming that widows correctly identifies the printer, if it says unknown device you may have a defective USB card.
http://www.themrpsolution.com/SearchResults.asp?Search=sato+usb&Submit=

Oct 28, 2016 | SATO Office Equipment & Supplies

1 Answer

How to install sato cl408e in windows 7


If your firmware is below 05.00.08.01
Then it won't get detected by windows 7. You will need firmware upgrade. Else, just go to www.satoworldwide.com and download the windows printer driver.

May 16, 2014 | SATO CL408e Label Printer

1 Answer

Hi, Sato CL408e, it starts printing between the labels. The feed is off by about 0.5cm. Any idea on how I can adgust that?


1) Try to calibrate the printer.
Else
do factory reset ( Press LINE and FEED At same time and switch on the printer.
Else
Change the potentiometer offset (Pitch,print) settings in the front panel.

Rgds
Mohan

Jan 21, 2011 | SATO CL408e Thermal Printer

1 Answer

How to calibrate


Hope this can be useful.No available information found to your quest.This is a Video Link for Media Loading.This other one Video Link is for Printhead Replacement

Jan 05, 2011 | SATO CL408e Thermal Printer

1 Answer

My network can't detect the new sato cl408e we just purchased.


1.Log into router
2. Verify wireless router name( on the computer) >>> ( on/off)
3.Note router name you are connecting to.
4.. Check the laptop,desktop,printer do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address.
6.Note router name you are connecting to.
7. Move the device about 20ft away and try to log on to the internet.
This is for all routers to set up wirelessly.

Jun 29, 2010 | SATO CL408e Label Printer

2 Answers

Pare parts in India for SATO CL408e printer


can better you to visit SATO website and get the information you wanted

Dec 27, 2007 | SATO CL408e Thermal Printer

1 Answer

Printer problem


check baud rate on NIC card (pull out NIC), against COM settings on PC. they must match. 9600 usually works

May 22, 2007 | SATO CL408e Thermal Printer

Not finding what you are looking for?
SATO CL408e Thermal Printer Logo

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top SATO Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

pkwc

Level 2 Expert

254 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a SATO Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...