Question about Locks & Locksmithing

Open Question

I have an ADESCO digital safe #US-25TE. I changed the batteries and now it cycles, says good, then red light starts blinking and I can't open the safe!!!!! HELP

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1913 Answers

SOURCE: Red power button blinking but tv won't power on

chec your ic register diode and transistor.
aslo check poer supply waltage and earthing properly.

Posted on Oct 11, 2008

  • 21 Answers

SOURCE: i cannot open my safe.

try holding the # and the * key for 5 seconds that should reset the safe and open it up

Posted on Dec 23, 2008

  • 2559 Answers

SOURCE: kdf-60xs955 red continous blinking lamp light

It's in standby mode.

Do a reset and see what happens

While holding down the reset button on the remote
Press the power button on the tv
(The tv will turn itself off the back on)
Now release the reset button

It sounds like the lamp needs replaced.

Please rate this a fixya

Posted on Jan 30, 2009

  • 3600 Answers

SOURCE: Door locked on safe

Brian We can't give advise on the safe but you can call the manufacture of the safe and if you have registered it they will help you otherwise federal law requires a lock smith to identify you and your information and your ownership of the safe before they will unlock it for you. This is to protect you or the safe owner and the lock smith from being sued and losing his licence.. There should be a sticker on the safe with a 800 number for you to call to get help. But you must have registered it first. They may have a way to verify it some other way but am not sure.

Posted on Nov 22, 2009

  • 21 Answers

SOURCE: Sentry Model 1610 Won't Open

here is the customer service phone number for you. I am sure they will be able to help you. 800-828-1438

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the battery compartment in my ce electronical digital safe?

do you have a round lock pad. This model has 2 9 volt batteries under the key pad

Lots of info here

  • How to open digital safe when battery is flat and key not ...
    • 1 MIN
    2012-11-09 · How to open a digital safe when the battery is flat and the ... How to open digital safe when battery is flat and ... How Secure Are Electronic Safe ...
  • Locked out of my Digital Safe [Archive] - PPRuNe Forums PPRuNe Forums > Misc. Forums > Computer/Internet Issues & Troubleshooting > Locked out of my Digital Safe. ... CE (Chinese made) electronic security safe ... battery ...
  • LA GARD LG Basic digital electronic safe lock changing ...
    • 3 MIN
    2009-10-13 · For instructions on this and other electronic digital safe ... How to change the combination and battery on ... Basic digital electronic safe lock changing ...
  • User Manual for Safe EA25 Installation - Tayabally EA25 Installation... You should change the code as soon as possible after opening the ... BATTERY REPLACEMENT. This safe uses ... MAINTENANCE FOR KEY AND ELECTRONIC SAFE.
  • Elektronischer Digitaler Safe Electronic Digital Safe · PDF file Electronic Digital Safe Version 12/08 ... (CE). Any usage other than ... Replace your batteries when both the red and green light illuminate. 1.
  • Instructions for an Electronic Digital Safe ' eHow > Home > Home Safety > Home Safes Instructions for an Electronic Digital Safe By Shawn McClain eHow Contributor Pin Share ... Replace the used batteries with new ones. For most safes, ...

  • Apr 24, 2016 | Locks & Locksmithing

    1 Answer

    Blinking lid locked light and green sensor light on machine won't start cycle

    The good ol' Whirlpool Lid Lock Flashing Light Problem - ApplianceBlog

    Dec 11, 2013 - 10 posts - ‎3 authors
    Red Lid Lock light flashing intermittently when you try to start a cycle. ... I'm going to post what SENSING does first, then you will need to locate your tech. ... start with thelid lock on and blinking, or the unit will not start and spin. FIXED Sense light on light humming noise won't start ...
    8 posts
    Aug 9, 2015
    Whirlpool WTW4950XW not working
    10 posts
    Nov 2, 2013
    Stacked GE washer/dryer lights Blinking doeent start at ...
    5 posts
    Feb 20, 2012
    More results from

    Washer Sensing led (Green) on with the lid locking led (Red ... > Manage My Life > Questions
    ... this: Sensing led (Green) on, the lid locking led (Red) blinking with a clicking noise ... red led light goes off green led light stays on and the washer does not start.

    Oct 27, 2015 | Washing Machines

    1 Answer

    How do i set code for paragon safe

    1. Remove the key plate cover, insert the key into the keypad and open the door.
    2. Remove the battery cover plate located on the inside of the door.
    3. Install 4 AA batteries provided and replace the battery cover.
    : If both the red and green lights are on while the safe is open, this indicates that the batteries are low and need
    to be changed.

    1. With the door open, locate the red button on the back of the door near the hinge.
    2. Press the red button and listen for the beep.
    3. Immediately enter your new passcode (3-6 digits long)
    4. Immediately after entering your new passcode, press the "A" or "B" button on the keypad. Your new user passcode is now stored.
    This safe stores up to 2 passcodes (a user code and a manager code). Entering a third code will erase the
    first passcode entered.

    1. Open your safe with the passcode you wish to change and leave the door ajar.
    2. Press the "0" button on the keypad twice. Press the red button, listen for a beep and then enter your new user passcode.
    New user passcodes may be 3-6 digits long.
    3. Immediately after entering your new code, press the "A" or "B" button on the keypad. Your user code is now changed.
    1. Input your code and then press the "B" button, the green light will turn on.
    2. Turn the knob clockwise within 5 seconds to open the door.
    3. Each key pressed will be accompanied by a buzzer and a yellow flashing light. If the entered code is invalid the yellow light will
    flash and the buzzer will quickly sound, this indicates the code needs to be re-entered.

    : Entering the incorrect passcode 3 times will lock the system for 20 seconds.

    More information can be found in the attached document web page.

    Aug 29, 2014 | Paragon Electronic Digital Safe Jewelry...

    1 Answer

    How to open a adesco safe if you have combination

    lost combination # i have floor model

    Dec 09, 2010 | Garden

    2 Answers

    I own a Bunker Hill digital floor safe sku #need code change data

    To change the code: Your safe comes
    preset with the default code of “159-A”.
    To change the code, first open the safe.
    On the inside of the door near the hinge,
    there is a small red “reset” button. Press
    this button until the Yellow LED on the
    front panel lights up. Now, input your new
    code up to 8 characters, followed by
    either “A” or “B”. The Yellow LED will flash
    to indicate that your new code has been
    accepted. Warning: If the Yellow LED
    does not flash, the code has not been
    accepted, and you must start over.
    NOTE: Be sure to test your new
    combination before closing the door.
    NOTE: Be sure to have the Override Key
    available when setting a new
    combination or changing batteries, in
    case the door doesn’t open.

    Good Luck

    Nov 15, 2009 | Sentry Fireproof Safe

    1 Answer

    When I placed my Lithium Ion Battery in the charger it doesn't carge the batter and the red light that's supposed to stay lit while it's charging keeps on blinking on and off.

    How old is the battery?

    It's very possible that the blinking light is indicating a bad/old battery. These rechargeable batteries after so many cycles lose it's charging capability and the fault system built into the recharging base will indicate by giving you the red light on & off. Energizer rechargeable station is a good example when it detects old or bad batteries.

    Nov 08, 2009 | Casio Exilim EX-Z57 Digital Camera

    3 Answers

    I have a model 45891 Bunker Digital Safe. Battery

    how do i change combination on bunker hill 45891 safe, i have tried every way i can think of.

    Oct 05, 2009 | Check Point Network Adapter

    1 Answer

    I cannot open my safe.

    try holding the # and the * key for 5 seconds that should reset the safe and open it up

    Dec 22, 2008 | Sentry Fireproof Safe

    Not finding what you are looking for?
    Locks & Locksmithing Logo

    Related Topics:

    112 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Locks & Locksmithing Experts


    Level 3 Expert

    76109 Answers

    ray gallant

    Level 3 Expert

    44310 Answers

    Tom Chichester

    Level 3 Expert

    34760 Answers

    Are you a Lock and Locksmithing Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides