Question about Jura Capresso Impressa F9 Espresso Machine

1 Answer

Why is my F9 dispensing coffee directly into the grounds container instead of out the spouts?

Looking into machine with tray assembly removed, using flashlight. I can see an inch or two of small black tube-like plastic or rubber hanging down near the flat round disc piece above the tray assembly.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jura Capresso Master
  • 1,316 Answers

From your description I would say a broken O ring seal in the brewing chamber. You will need to remove the brewing unit and clean, replace seals and lubricate the sliding guides.

Posted on Dec 08, 2014

  • Debra Tomaski
    Debra Tomaski Dec 09, 2014

    As soon as I manipulated the black dangling piece, it fell off completely and does appear to be a broken O ring seal! Will update on progress as repair progresses. I'm so impressed by getting such a prompt and knowledgeable (and evidently accurate) reply! Thanks to Mr. Keen! Wow!

  • Debra Tomaski
    Debra Tomaski Jan 01, 2015

    Update: while your answer is correct, my husband decided it would be worth replacing the entire brew unit, since very little time had passed since his last repair mission for this machine. We received the replacement unit and it seemed to fit well. However, when we turned on the machine, we heard tortured-sounding metal-on-metal grinding that alerted us immediately that the repair would not succeed. My F9 was 7 to 10 years old, and I used it A LOT. Sadly, we had to let go and set it free. LOVED that thing. I now have an Academia Gaggia, and it is gradually winning me over and restoring my will to live. Thank you so much for your help. Without it, we'd still be working on the disassembled Jura and hating life. Many thanks. Mr. Keen; you know your stuff! Debra

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot install tray with ground basket installed, after removing. Mechanism is blocking the ground basket when the tray is slid back into the unit after emptying.


Try putting a container under the coffee spouts and pressing the rinse button. This will usually free any coffee grounds that may not have been expelled into the grounds basket from the last time the machine was used. The grounds can get stuck and block the slide path of the grounds basket.

Dec 23, 2010 | Jura Capresso Jura / Capresso IMPRESSA J5...

2 Answers

Will not dispense the water into the cup when the button is pushed


I have had this issue. First, check to make sure water tank is filled and correctly in place? Try descaling it; a kit came with coffee maker. (It just removes hard water build up, it may be blocking your water flow.) If that is not the issue, pull the tray where the used pods are dropped -Is it wet? Like the coffee is pouring into this tray rather than in your cup? If so, I have removed round silver plastic piece from around coffee spout,(gentle -do not crack it) then removed and washed the black spout, I even used a toothpick once, to remove the stubborn coffee ground, Once it was cleaned - it worked perfect. If you run water from the faucet into spout it should flow smoothly. I warn you though, not sure what this does to any warranty, but don't mess with my morning coffee! If the POD tray is not wet, I would tell you not that most likely your machine is not clogged by grounds, so you may not want to take snout apart. I hope this helps.

May 02, 2010 | Nespresso Essenza C100 Espresso...

1 Answer

Tray will not insert properly, a flap seems to be lowered


Start up the machine, take insert everything but the used grounds container. The machine will reposition the brew unit. When the machine says "heating", take out the tray and now you can insert everthing with the used grounds container. You can of course run a Rinse cycle if the machine doesn`t start positioning right away.

Aug 30, 2009 | Jura Capresso Impressa F9 Espresso Machine

3 Answers

Both spouts seem clogged


I have a Jura Impressa F7 that had the exact same issue. To solve it was pretty simple. Try and make a cup of coffee, and while the machine is trying to pump the coffee thru the spouts, grab the chrome handle on the spout and vigerously move it up and down rapidly. You should notice small grounds of coffee dislodge and follow the stream of coffee into your cup. If you do this a couple of times, you will be able to clear the trapped grounds within the spout. Hope it works for you as well as it worked for me.

Jun 23, 2009 | Jura Capresso Impressa F9 Espresso Machine

1 Answer

Water not coming out of dispensing area, goes to drip tray instead Water comming out in drip tray instead of regular way


Try this, if the machine has a pregrind door(usually on the top front) then use the button to tell it you are using pre grind coffee, if water comes out the spout this way then the grind on the grinder is too fine, if it goes out the drain then the coffee passage is blocked, remove the brew unit and check/clear tubes, also clean the spouts on the door of the unit.

May 30, 2009 | DeLonghi Esclusivo Magnifica ESAM3300...

1 Answer

No coffee will dispenses


I would remove the coffee spout and check the lines into it. The coffee seems to stop when it hits the spout and goes through the by pass instead. Remove the spout(be careful) then run a coffee and see if it works.

May 24, 2009 | Jura Capresso Impressa E75 Espresso &...

1 Answer

Saeco Talea Giro no steam or water from spout


I have the same problem as well, talked to a repair shop and it's definitely a "send in" or warranty repair. I was told it's an o-ring issue. I have no water coming out of the steam wand and it goes into the dispense tray instead.

Apr 11, 2009 | Saeco Talea Giro Espresso Machine

2 Answers

Jura Impresso E9 not dripping through spouts but into drip tray


This is most likely due to a bad o'ring. The bar you speak of...Does the unit have a small spout pointing upward from the area?...with a groove? Is the o'ring in that groove damaged or missing? When the grounds are compressed in the piston, the brew unit lowers down onto this spout and seals on it. The high pressure water then is injected upward inot the brew unit. When this seal fails the water simply leaks into the tray when there are grounds providing backpressure. When rinsing and no backpressure some of the water may be getting through. Make sure you lube up any seals with a food grade lube. Olive oil will work in a pinch.

Mike

Feb 05, 2009 | Jura Capresso Impressa E9 Espresso Machine...

1 Answer

Leaks at the hot water spout during coffee brew


I had the same problem. I ended up taking the coffee machine apart and found that the reason coffee trickles out around the hot water spout is that the two coffee nozzles were partially plugged. Since I Had parts of the coffee machine apart I was able to clean it easily. It may also be possible to clean the assembly using a pick of some sort and clean out the holes of the two normal coffee spouts. Inside it is just a open cavity so gentle poking around and using some steaming hot water may do the trick.
If you want to take the machine apart you need to do the following: 1) take of the warmer plate on the top - 2 storz screws but an allen key works as well 2) take off the top plate of the machine - another 4 or 5 screws - make sure you empty the beans first otherwise you will have a mess 3) remove one screw from the right hand side of the removable coffee ground tray. Once this screw is removed the front panel is free to swing open except for the pipes connecting the front 4) unclip the steam assembly - there are a couple of plastic catches on the top. this will free the steam assembly from the front panel and also free a pipe connections. The steam dispenser pipe will also come free from the steam assembly. 5) remove the coffee pipes from the up and down sliding coffee dispenser. This is a small whitish color clip with 2 pipes connecting into it. The white clip has a little plastic catch on the top that frees it. The front panel should now swing open freely. 6) remove the sliding coffee dispenser from the front door. There are 4 plastic catches, 2 on either side. the whole front sliding coffee displenser now comes free 7) Take the sliding dispenser apart by release the 4 plastic catches on the front curved planel. 8) Inside the sliding dispenser is a white plastic piece that connected to the piping released in step 5. There is a small plastic catch that needs to be pressed while pulling fairly hard on the plastic piece and bending the whole piece. 9) You will now see the plugged spouts. It goes back together really easily.

Aug 13, 2008 | Jura Capresso Impressa S8 Coffee Maker,...

Not finding what you are looking for?
Jura Capresso Impressa F9 Espresso Machine Logo

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jura Capresso Coffee Makers & Espresso Machines Experts

The Knight
The Knight

Level 3 Expert

75571 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ken Macumber
Ken Macumber

Level 1 Expert

12 Answers

Are you a Jura Capresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...