Question about Washing Machines

1 Answer

Kenmore He4t front load washer f 06 error code

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

This answer is actually from Sears Parts Direct: The F06 error code
indicates a drive motor tachometer error. This error is virtually impossible to accurately diagnose. The most suspect components that would cause this failure code are the drive motor, the motor control unit (control board) or the wire harness. In some instances, this could be caused by severely overloading the washer so that it cannot spin properly. Make sure that the washer is not overloaded. Another problem that could cause the error code to be displayed intermittently would be a loose wire harness connection that is affected by vibration when the washer is spinning at high speed. Good lucks, hope it helps

Posted on Dec 07, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jsrock516
  • 5911 Answers

SOURCE: kenmore elite HE4T front load washing machine standing water

This problem can be caused by either a leaking water inlet valve, or a condition known as "siphoning". Since you just recently moved, I would make sure you don't have a siphoning problem, first. The following link explains how:

http://www.fixya.com/support/r587481-prevent_washer_siphoning

Although siphoning normally refers to a constant drain problem where a washer has problems maintaining the proper water level, it can also lead to problems where the drain line will back up into the washer.

Now, if you follow the advice in the link and determine this is NOT caused by siphoning, I would suspect that you have a water inlet valve that is leaking. A tell-tale sign will be water trickling down the fill tube in the rubber door bellow. The water inlet valves have a diaphragm that is controlled by an electric solenoid. Sometimes the valve becomes clogged with sediment or deposits, causing the diaphragm not to close properly. If you live in an area that has hard water, or use well water, you may have hard water deposits or rust build up in the valve. You may be able to correct the problem by removing the valve and cleaning it with some distilled vinegar. You can remove the valve by following these steps:

1. Unplug the washer and turn off water supply at the taps.
2. Disconnect the water inlet hoses.
3. Remove washer top panel by removing the three screws that hold the panel in place in the rear of the washer. With the screws removed, the panel slides back, then off.
4. The inlet valve (this is what your water inlet hoses connect to) will be located in the left rear of the washer (facing from the front). Remove the dispenser hose(s) from the valve and the electric connections. Remember how the electrical connections are removed. They should be color coded. One is for HOT, one is for COLD.
5. Remove the mounting screws that hold the assembly in place.

Once you have the inlet valve removed, you can place it in some distilled vinegar and let it soak. Just don't submerge the electrical connections. If this does not correct your problem, replace the valve. Searspartsdirect.com and repairclinic.com are two notable web sites that I have frequently used. Just type in your complete model number to begin the parts search.

I hope you find this information helpful. Let me know if you require additional assistance.

Posted on Sep 02, 2008

jyackle5
  • 8197 Answers

SOURCE: error code f24

F24 indicates a water temperature sensor error. If during the wash cycle in the water-heating step, the water temperature sensor (NTC) value is out of range the F24 error code will display.

Possible causes:

  • Too cold of water or hot water is turned off
  • Temperature sensor failure or loose connection
  • Control board failure

Posted on Dec 18, 2008

  • 3741 Answers

SOURCE: Washer stops with F11 code; door won't open

F-11 ERROR CODE MEANS :

Serial Communication Error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

TO RESOLVE THE PROBLEM:


  • Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU)

  • Check the Drive system for any worn or failed components

  • Check MCU

  • Check CCU

  • Check Motor

  • Check Wire Harness


Posted on May 05, 2009

Krazytech
  • 725 Answers

SOURCE: kenmore he2t error code 21

F21 is a long drain...it is taking too long to drain..you have a something slowing down the drain.. you can remove the bottom panel and clean out coin trap... if there is nothing then you may have another problem... but this is the most common problem..

Posted on Sep 23, 2009

  • 1 Answer

SOURCE: Kenmore HE2t washer - error code 5d

5d is a definitely a the code for a plugged discharge. We removed the lower access panel and discovered a virtual treasure: $12.50 in quarters, nickels, dimes and pennies, a pen, a pencil, collar stays, 10 bobby-pins, 3 barrettes, a elastic headband, a draw string, a box cutter, 3 washers, 3 broken zipper parts, a elastic waist band. Amazing it took all to trigger a 5d error code. Hope this helps!

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting a f33 error on front load kenmore HE4t already changed the pressure switch and flow meter but still get f33 error


The F33 error code indicates a pump drive system error. If the pump ohms out correctly & the harness is secure I recommend replacing the CCU (central control unit).
Please see the following image provided for instructions.

http://media.fotki.com/1_p,stwwfrggtqfbrbbxgtqsskgwtqkq,vi/wgtbwqwssxsbwkbdtfwxrbfbddwwf/1/1303472/5961857/image9159087223444281043img-or.jpg

Remember to disconnect power to the washer before attempting access.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 22, 2010 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

HE4t Washer


"F06" is a Motor Speed error. The following link explains how to troubleshoot and some common causes:

http://www.fixya.com/support/r714929-f06_error_whirlpool_duet_kenmore_elite

The first step to troublehsooting should be to unplug the washer for AT LEAST 30 minutes in an attempt to reset the Central Control Unit (CCU). Sometimes this is all that it takes to correct momentary glitches with the unit. If the error code reappears following a computer reset, follow the advice given in the link I provided.

If you have questions, or require additional assistanc, please let me know. I hope this helps you.

Jan 23, 2009 | Kenmore Elite 45986 Front Load Washer

3 Answers

Kenmore Elite HE4t washer won't spin


The motor controller board is likely bad.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 06, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore he4t washer shows f-11 error


F-11 // WILL THEN APPEAR FDL CODE DOOR LOCK LOCK FAILURE, F-11 COMMUNICATION ERROR REPLACE MAIN CONTROL,, JUST REPL 3 TODAY ....

Nov 28, 2008 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

F Code for the Kenmore Elite he4t Front Load Washer (3 years old)


Hi! ricksmith
What is the first three digits of the model number.
The he4t I have reference to does not have a "F" code error. Most of the codes are two digit, PF, F1 to F9 etc.
You could try: Pressing Pause/Cancel two times to clear code. As well as unplug for 20 seconds. Do you have power fluctuations in your area.
InMrFixIt

Aug 27, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore elite error code


possible electronics failure. my HE4t has completly gone dead at the control panel after displaying error codes. A class action law suite is in the works on the HE3t HE4t machines.

Aug 20, 2008 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...