Question about Jura Impressa Z7 One-Touch Automatic Coffee Center

1 Answer

Jura z7 error message empty coffee tray when tray s not full

Error message to empty coffee tray when the tray is not full

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 80 Answers

Yo James,

I know nothing of your unit, but I've never let that stop me before??.

Sounds like a sensor is stuck in the "tray full" position and popping an error message based upon what "it" is detecting.

OK, how does the unit know from "full tray" (what ever that means). I'm a big believer in problems being created by dirt, crud and in your case, coffee grounds. Unless the sensor (switch?) itself has failed, I'll bet there is debris fouling the system.

Find the "full tray" (what ever that means ??) sensing mechanism and clean/replace it and I'll bet you will solve the problem.

All the best.

Posted on Dec 11, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Switched propane tank and no hot water why


The pilot light went out because the gas supply was interrupted? They usually have two tanks and an automatic switchover in a domestic situation. You change the empty one before the full one runs out.

May 24, 2016 | Water Water Heaters

2 Answers

Why does the coffee brew all over the counter, on cuisinart doc-1150?


Dear Friend,
Make sure that there is nothing interfering with the brewing process such as small particle of coffee been stuck between the jar and the brewing funnel on top that can cause any clog. Used coffee paper filter if you are not using.

Good Luck

Sep 20, 2014 | Cuisinart DCC-1150BK 10-Cup Programmable...

1 Answer

Cabrio Washer Problems


That error means that it is sensing an OVERLOAD. If it does this when it is empty, then there is something causing the error. IT could be something stuck in the drum around the seal or the bearing or it could be the bearings itself

May 02, 2013 | Whirlpool WTW8200YW 4.6 cu. ft. Cabrio...

1 Answer

Rheem Eco Sense PTG2-42PVV error messages


Open following link for rheem tankless resources, including error codes and typical maintenance.
http://waterheatertimer.org/Troubleshoot-Rheem-Tankless-water-heater.html

May 18, 2012 | Water Heaters

1 Answer

My water heater error code 1 model ee3250rd055v what does this mean


Water heater is not 100% identified.
Unknown if this is gas or electric heater.

Problem posted under Whirlpool water heaters typically made by American water heater company.
Call Whirlpool 877-817-6750.
They will ask for model number and serial number located on label on side of tank.
Call is answered in USA by trained person who can answer specifics about that model, including warranty, age, regular maintenance, error codes, and possible solution for that specific model and serial number.
I have found these folks to be helpful.

Whirlpool manuals do not show that specific model:
http://www.whirlpoolwaterheaters.com/support/manuals.aspx

If you have the energy smart electric water heater with electronic control board, then error code explanation shows on the control board. Error 1 or a single flash, is start-up failure and requires tank to be full of water. Read page 10 of manual. Make sure water heater is full of water and water is coming full stream out of tub spout before turning on power. Also disconnect power from unit, make sure water heater is full, and then reconnect power to see if unit resets.
http://waterheatertimer.org/Whirlpool-Energy-Smart-electric.html
http://www.whirlpoolwaterheaters.com/downloads/6510306.pdf

Sep 12, 2011 | Whirlpool Water Heaters

1 Answer

Dsi flt light keeps going on and the black water light says full when we just emptied it.


DSi light coming on is to alert you that the water heater didn't light on propane for one reason or another. Sometimes people just forgot to turn propane on or are out of propane. What happens when you shut it off and turn it back on? (listening and watching from outside with cover open) DO you see or hear sparking?

As far as black water showing full when just emptied, it is most likely a piece of toilet paper inside the tank that is hanging up from top probe on inside of tank, and touching lower probe, thus giving a full reading. This is very common, at all levels. You can buy a rinse wand and rinse inside of tank through toilet to try and wash it off, or live with it for now, and add lots of water or cleaner deodorizer to tank , or buy probe cleaner, or even the old standby, some laundry soap added to tank , then fill tank close to full with water and rock trailer to swish it around, then drain it. Most times, waiting until next dump, and adding lots of water beforehand, will fix it.

Jul 11, 2011 | RTO Atwood DSI-RV Water Heater-6 Gallon

1 Answer

Empty boiler


Turn main water off to the water heater, it may be a valve on cold side coming in to shut off. Next turn power off to the heater and drain the tank the drain will be located near the bottom of the tank.
You will need a water hose to connect to the drain to run water outside. Open a faucet hot side to allow you to drain the tank.

Upon reinstall connect the tank up and fill tank and open up hot side on one faucet at a time to purge out air from system before turning power back on. Make sure you have water flowing from each faucet's hot side before turning power back on.

Jul 02, 2010 | Rheem 80 GAL ELEC TALL Water Heater 6YR SC...

1 Answer

WHAT DOES THE ERROR MESSAGE F76 MEAN?


1/ check overheat stat 2/ check fan esp the little hose at the fan area for pinhole best of luck

Sep 28, 2009 | Noritz 6.9 Gallon Residential Tankless...

6 Answers

Paloma heater shuts off


I've installed a number of these units and the C4 76 error code is a bad PCB board. The remote unit is not communicating with the PCB board so you need to call customer service at 800 432 8373. You'll need to give them your name, address, model number and serial number. They'll send you a new PCB board with instructions on how to swap it out. It's pretty easy.
Meanwhile, you might be able to get hot water while you wait the day or two for the replacement parts to arrive by simply disconnecting the wires from the remote at the PCB board. This works about 50% of the time. Once they're disconnected try turning on the hot water full blast and see if the unit fires.
Good luck with it.
Paul (Redwood City, CA.)

Apr 03, 2009 | Water Heaters

Not finding what you are looking for?
Jura Impressa Z7 One-Touch Automatic Coffee Center Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jura Water Heaters Experts

Donni Steen

Level 3 Expert

659 Answers

Brad Brown

Level 3 Expert

16031 Answers

Gil Shultz

Level 3 Expert

3368 Answers

Are you a Jura Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...