Question about Zanussi Washing Machines
Cannot fit spring into the door seal
This is not easy and there is a real knack to it. You will find it easier to have a second person helping. One holds the spring in position at the top and the other at the bottom and roll the spring over your hands into the slot
Posted on Aug 16, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: I am trying to fit
Its a tricky one but the easiest way is tolubricate the inside of the flap with wash up liquid then starting at bottom feed it on bit by bit following round with other hand to stop it slipping off. Once on its easy to rotate into correct position.
You will need an extra pair of hands to help with the spring.
Hope this helps & thanks for using Fixya.
Posted on Jan 10, 2009
Fit the seal first and then fit the spring,it cannot be done with the spring fitted on the seal first.
Plz rate my solution.
Posted on Jan 18, 2009
Follow these steps to replace your door
For all Free appliance repair videos visit our VIDEO TUTORIALS
Disconnect all power to the machine first!!
1 Locate the outer clamp band securing the seal to the door rim on the washing machine and examine it carefully for holes or tears. Many can be prised off with a flat-bladed screwdriver they have a spring system holding them, but some have a tensioning arrangement that has to be loosened.
2 After removing the outer clamp band, locate the inner one securing the seal to the drum and establish how this is secured. It may be necessary to loosen a clip, or you may be able to prise the band off with a flat-bladed screwdriver. Some are like very large Jubilee clips that you have to undo usually from the top.
3 Once the clamp bands have been removed, use both hands to pull the seal away from the inner drum rim. Some machines have a water spout holes that will have to be lined up. Others have a drain holes.
4 Rubbing a drop of washing up liquid into the groove on the door seal/gasket that locates on the drum makes fitting the new seal easier.
5 the new washing machine door seal should be fitted by locating the drain holes at the bottom of the seal first then push it on with both hands working opposite directions towards the top. This is quite hard if you have never done it before.
6 refit the inner band remembering this must be tensioned correctly for it to be water tight.
7 now fit the outer band and the test the machine for any leaks,
All washing machine spares featured in this article are available at apart4u with more video help in our tutorial section.
Information provided is a guide only. aPart4u accepts no liability for any problems occurring whilst attempting any advice shown. If in any doubt about fixing your appliance, always contact a qualified repairer.
Posted on Jan 19, 2010
Tips for a great answer:
Sep 10, 2017 | Zanussi Washing Machines
Dec 04, 2014 | Zanussi ZWF1430W Front Load Washer
Aug 21, 2010 | Whirlpool Duet 3.8 cu. ft. Front Load...
Mar 12, 2009 | Zanussi FLA1201W Front Load Washer
Jan 17, 2009 | Zanussi WJS1265W Front Load Washer/Dryer
Sep 28, 2007 | Washing Machines
Mar 27, 2007 | Zanussi FLA1201W Front Load Washer
Feb 24, 2007 | Zanussi FS1255S Front Load Washer
Feb 05, 2007 | Zanussi IZ161S Front Load Washer
Aug 04, 2006 | Zanussi FJS1225W Front Load Washer
Oct 07, 2017 | Zanussi Washing Machines
81 people viewed this question
Usually answered in minutes!