Question about Welding Tools

Open Question

Operate BOC 200C welder,mainly the 1 or 2 inductance settings

Posted by on

  • Andrew Smart
    Andrew Smart Dec 05, 2014

    yes i got answers from arc-i welding in osb pk and finally from BOC welshpool

    Yes the inductance settings can be used independantly of voltage controls

×

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: mig welder tripping power supply

the breaker could be bad. try to change the breaker

Posted on Jan 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Induction fault e6


E6 - Defect Induction module or over temperature of coil sensor with Falcon User interface with production date before 2010

Defect Induction module
- Disconnect the appliance from the mains for 30 sec. If alarm still occurs after 1 min operation exchange induction module.

Over temperature of coil sensor with Falcon User interface with production date before 2010
- temperature sensor defect or wrong mounted.
  1. Check connector at induction module.
  2. Check the coil sensor, it should be placed even in the silicon carrier.
  3. Appliances with 3 zones, is the "Dummy" temperature sensor at the 2nd terminal mounted?
  4. Exchange coil with sensor.
  5. If above is without success, exchange induction module.

24569233-wjkdtau3hzetwygkyoujq3j4-2-1.jpg
Dado

Jun 03, 2014 | AEG Ovens

1 Answer

Do you have the internal wiring diagram for the bx1-200c welding machine


Sorry I'm not familiar with Chinese welding machines.

Dec 02, 2011 | Welding Tools

1 Answer

Ford powered hobart welder parts manual


Hi:There are no induction coils, transformer part number is HOB 217096.You can go to our website and order it.http://www.praxairdirect.com/webapp/wcs/stores/servlet/TopCategories1_10152_10051_-1
Have a good day.

Nov 09, 2011 | Hobart Handler 140 Mig Welder

2 Answers

My new Miller Bobcat has low amperage on 120 volt outlet.


Increase your idle setting on the 1/8" threaded rod protruding to the left of the carburetor until V= 125. Then run your drill. Actuating the drill should call the throttle solenoid to open up to produce more power.

May 12, 2010 | Miller Electric Manufacturing Electric...

1 Answer

My Bosch HBN 5605 .0B oven has a 15-20 degree undertemperature when operating on the conventional baking setting - all other settings are ok


I detected a similar problem following the sudden appearance of Err1 in the display. (Oven 4-5 years old, and the grill element failed when it was 3-4 years old). This indicated a temperature sensor problem. My local dealer came with his Thermocouple and confirmed an "under temperature" reading on the standard and baking settings. I agree that the fan setting is probably OK. He replaced the sensor. I monitored the situation for a while and was not happy because an under temperature could be quite dangerous when cooking certain foods, and also causes problems when baking bread.

The location of the oven sensor is also a problem because it is at the top right by the grill which also serves as the top heat source.

I had corresponded with Bosch about this and their response was, frankly, less than satisfactory. In the end I decided to call out their engineer (cost £85-ish) who wired my oven up to his computer. In the end he said that the oven was working as it should be (despite it taking a very long time to actually reach the target temperature of 200C.

In my view of I want 200C, then I should get 200C, not an approximation.

Interestingly the secret info (not in the manual) is that the temperature bar readout does not indicate that it has reached the actual temperature, but may be 90% of the temperature (so if you want 200C you get 180C.

An unsatisfactory solution is to get an oven temperature of the meat probe type and put that in the oven, then you will get a more accurate reading of the temperature. You would need one that goes above 200C (my first one only goes to 200 but I have found another that goes to 250C). Mine is by CDN model DTP482, any good cook shop should stock this.

Andrew Finch

Jan 02, 2010 | Bosch HBN 430560B / 430520B Single Oven

1 Answer

Mig welder tripping power supply


the breaker could be bad. try to change the breaker

Dec 09, 2008 | Troy MIG100 90-Amp. Wire Feed Welder

Not finding what you are looking for?
Welding Tools Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Welding Tools Experts

Brad Brown

Level 3 Expert

15441 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Bill Boyd

Level 3 Expert

40672 Answers

Are you a Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...