Question about Ruud Heating & Cooling

1 Answer

Ruud Silhouette II has power but nothing else.

It has power going to board. The lights for codes don't light checked fuse and its good. Cleaned sensor and igniter. Bypassed thermostat with jumper from R & W still nothing. Checked glass fuse and its good . This thing just sits dead please advise.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 113 Answers

Sounds like there is a secondary fuse protection, or some wire came off. Did you check for ground?

Posted on Dec 03, 2014

  • Steve Roberts
    Steve Roberts Dec 03, 2014

    No I didnt. My testers batterys died. I will try today. Thank you.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code lights won't light on rheem ruud 1028-928


That board runs on 24v power. I would check to see that you have 24v from C to R at the t'stat wire terminals. Also make sure that the fuse is in place and that it is good.

Dec 01, 2014 | Ruud Heating & Cooling

2 Answers

My RUUD PVRP75 has no power, no red light


CHECK BREAKER , POWER AT UNIT IF GOOD BAD TRANSFORMER IN UNIT ,

Aug 17, 2014 | Heating & Cooling

2 Answers

Rudd silhouette ii blower


Send direct power to the blower by bypassing relay . See if motor runs

Jul 19, 2017 | Ruud UBHC Air Conditioner

2 Answers

Ruud Silhouette II Gas Furnace, purges, lights burners and burns until the blower starts and then burner stops and does not really blow very warm air. Once blower shuts off, it starts the process all over...


Flame sensor needs to be cleaned. turn off the furnace power switch or breaker. pull the flame sensor located in the burner runner section of the furnace. It will be easy to locate because it has 1 wire running to it. pull the screw being very careful not to harm anything else. get the sensor out. inspect it for cleanliness. clean the sensor with light grade sand paper gently. re-install the sensor plug the wire back on. restart your furnace and this should fix the problem.
CookHVACR

Nov 19, 2010 | Heating & Cooling

1 Answer

I have a RUUD Silhouette II and while it was running the thermosat wires hit the top of the unit, there was a spark and it died. I checked all the breakers, but still nothing. When I turn the unit power...


Hello CHARLIE Yes that was a 24 volt wire that got shorted 1:The wire must be repaired/replaced.2:The fuse is in the blower/airhandler unit it should be a 3 or 5 amp blade fuse (the one that is in a car) on the curcit board, or a button that poppes up on transformer in the blower unit just push that in to restore low voltage power.

Sep 03, 2010 | Heating & Cooling

1 Answer

No Power to Circuit Board


No control voltage 24 volts. The fan board if it has one. sometimes has a five amp auto fuse on it. If not sounds like the transformer. Not hard to replace.

Jun 14, 2009 | Ruud UBHC Air Conditioner

2 Answers

Ruud Silhouette II Fails to Ignite


sounds like you have bad flame sensor or the sensor is in a bad postition. To get eliminate the lockout turn the power off to the unit and back on again. Look at the circuit board light and see what the troubleshooting code is.

Jan 13, 2009 | Heating & Cooling

1 Answer

Flashing amber lights


it means that the flame sensor is not sensing a flame. If the flame is present and nice and blue the flame sensor is probaly dirty. Remove the flame sensor and lighty sand it with sandpaper.

Dec 25, 2008 | Ruud UBHC Air Conditioner

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ruud Heating & Cooling Experts

Donni Steen

Level 3 Expert

659 Answers

Bill Long

Level 3 Expert

587 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Ruud Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...