Question about Pool & Spa

1 Answer

Pool pump would not start , flashing red error light

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 149 Answers

Could be many different things. Shaft locked up? Low voltage? Bad start relay. Bad start windings. Red light signifies what? Have an operators manual? Hard to say at a distance.

Posted on Dec 03, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Motor red error light comes on, pump won't turn on


if power to motor bad pump motor if no voltage to motor bad relay

Mar 01, 2015 | Marathon Electric Marathon imPower...

1 Answer

Reset Jandy PS6, still flashing red and green


turn off heater if ok then replace ignitor if not keep removing auxs until stops blowing breaker

Apr 02, 2014 | Jandy Aqualink Pda Ps6 Wireless Handheld...

1 Answer

Lanark spa bath


Not really sure but it sounds like there is a sensor that may not be reading properly preventing the pump to turn on.
Rod @ US Parts Center

May 12, 2013 | Pool & Spa

1 Answer

Hydro-Quip pack in my Hydro-Spa hot tub no heat.


Hi,
3 Flashing dots (display) - Water flow problem check for closed valves, dirty filters, water level, pump/wet end operation/defective pressure switch.
If your spa has been off for a while its likely something is blocking the lines.
Flashing dots & Lit light on display - Hi-limit trip, reset power to clear.

Nov 16, 2011 | Hydro Quip Inc Pool & Spa

1 Answer

Timmer switch turns on but pump does not start. I have to go out and turn off timmer swith for a few seconds and turn timmer back on and pump usually starts auto matically. Some times when timmer switch...


The flashing re light is trying to tell you what is wrong! It will flash 2 to 9 times and you need to count the flashes and then refer to the troubleshooting chart on page 27 of your owners manual.

To me it sounds like your pump loses it prime some I would suspect a leak on the suction side of the system.


http://www.inyopools.com/manuals/210/IntelliFlow4x160_OM.pdf


Jul 20, 2011 | Pentair 4-Speed 230v IntelliFlo 4x160...

1 Answer

My glowbouy flashes green and red...what does this mean


According to the owners manual for these swimming pool lights, this is what each colored indicator means. Hope this helps.


Solid green
The battery pack is fully charged.
Slow flashing green
The battery pack is almost fully charged.
Slow flashing yellow
The battery pack is half charged.
Medium flashing yellow
The battery pack is less than half charged.
Fast flashing yellow
The battery pack has almost no charge.
Fast flashing red
A charging error has occurred and the light should be unplugged and then plugged back in. If the Fast Flashing Red persists after several attempts, the battery condition is questionable.



Also in the trouble shooting guide, it mentions this:


Problem: Red Indicator Light Is Flashing While Charging

Solution:
A red flashing indicator light when charging indicates a selftest
error condition. Unplug the product and plug it in again.
Try this several times; if the indicator light continues to flash
red, unplug the GlowBuoy and take it to an authorized service
depot.

Oct 22, 2009 | NRS CANTAR GLOW BUOY FLOATING POOL LIGHT...

1 Answer

AquaLink RS 4 top lights flashing red bottom lights flash yellow


I don't have the "one-touch", but on the "all-button" there's a hole on the left side of the unit. A paperclip inserted in this hole will reset the unit. I had a problem with the display on mine and this fixed it.

Apr 19, 2009 | Jandy Aqualink Rs4 One Touch Control...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1343 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

5706 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...