Question about Canon iR3035 Copier

2 Answers

How to change the fixing film on a cannon printer IR3035

I took it apart and got to the fixing film but how do I know if it needs to be replaced. it will go for a week with no problems then show the error code that its temperature got to high

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Canon Master
  • 434 Answers

Usually error in fixing unit are related with fluctuating energy problems. Clear the error from service mode if problem persist. Replace the fixing heater unit

Posted on Mar 22, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer got voted for 20 times.

  • Canon Expert
  • 234 Answers

Try to replace it,and U'll see

Posted on Dec 29, 2014


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 57 Answers

SOURCE: Wrong Cartridge Error Message

The Print Head might be the fault of that,try replacing the print head and see if that helps

Posted on Nov 27, 2007

  • 1 Answer

SOURCE: Cannon PIXMA MP520 Problem: Error code

I had this problem with the ink carriage jammed at the left hand side of the printer. I operated the lever in a hole on the top left hand side and eased the carriage along to the middle and pushed it back onto it's runners. All OK now.

Posted on Jun 29, 2008

  • 1 Answer

SOURCE: Wrong Cartridge Error Message

Thanks for your assistance....worked on it for a couple of hours still no success.....guess it is time to buy a new printer....this one is 6 years old and I quess it doesn't owe us anything......Our previous NEC lasted 10-12 years if not longer.... so in the long run we have faired well.....Don't want to spend the mopney on a cartridge when the sytem is old and may fail in some other way.

I am looking to purchase an HP combination printer to replace this one.........any thoughts.

By the way this is the best site for information on resolving any problems that I have had with my computer and accesories.

Posted on Aug 17, 2008

  • 3614 Answers

SOURCE: Cannon Ip4300 - Orange light flashes on printer.

Hi there,

A possible paper jam has happen on the unit. Did you have an paper jam error before you have this problem?

You must clear any paper jam on the unit, check the unit for any stuck paper or object or check if there was misaligned parts inside.

Let me know for any clarifications.

Thank you for using fixya.


Posted on Dec 12, 2009

  • 74 Answers

SOURCE: cannon pixma mp145 printer error code e7 & e2

E2: Reload the paper correctly and press [Black] or [Color].

E7: The cartridges are not installed in place.

These are from the manual.

Posted on May 10, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


The error indicates the abnormal rotation of the fixing film. Mostly the film tear off at fixing film assembly. The film may be replaced at less cost as 3rd party service or the fixing film assy. replaced as geuine spare.

The other problem may happen, as rotation sensor failure or DC-CON pcb. but these are very rare.

Mar 05, 2015 | Cannon Office Equipment & Supplies

1 Answer

Cannon image runner 2420 error 000007 how can i fix?

It's a problem with the fixing film in the fuser assembly. The fixing film shredded and needs to be replaced.

Since part of it is probably gone, the length between the 2 plastic end caps.

This could get involved. Two Youtube presentations are below. Maybe one of them shows how to replace the film. They appear to be for dis-assembly and removal of the fuser unit. The source of fixing film has a nice picture of what needs actual replacement.,d.dGc

A source of fixing film:

You don't want to get cut, shocked, or covered in ink while doing this. Sadly, this is where a little knowledge is a dangerous thing. A Cannon tech or your printer support would be well versed in doing what needs to be done.

Mar 05, 2015 | Cannon Office Equipment & Supplies

1 Answer

Error code e0000003-00000

low temp detected at the fixing film assy.
- Check the connector of the fixing film unit.(thermistor and its harness)
- Replace the fixing film unit.(chect the heater contact points up to smps)
- Replace the DC controller PCB.

Considering supply voltage is within the specified limit.


Feb 28, 2015 | Canon Office Equipment & Supplies

2 Answers

How to fix error e000202-0001 for canon ir3035?

How to fix error E000202-0001 for canon ir3035

Jul 17, 2014 | Canon iR3035 Copier

2 Answers

My xerox machine cannon IR 2020 shows a system error E007. How can I solve it? Please describe step by step.

E007 - Fixing film rotation error

You have to disassemble fuser unit and inspect a fixing film, if damaged - replace.

The official documentation says:
E007 0000 Fixing film sensor failure
The fixing film sensor is faulty. - Check the connector of the fixing film
- Replace the fixing film sensor.
- Replace the DC controller PCB.

Nov 11, 2010 | Canon iR 2022 Printer

2 Answers

Cannon ir2018 system error E007

E007 is fixing film problem. Worn-out fixing film.

Sep 28, 2010 | Canon iR 2016i Black and White Copier

1 Answer

Cannon mf6500 gives system error 007 when switched on

Dear Sir,
Welcome to Fixya

The problem is with the fixing film, it has a sensor on one side that is were the film is torn. replace the fixing film.It deffinately solves your problem.

Have a Nice Day!

Nov 12, 2009 | Canon imageCLASS MF8170C All-In-One Laser...

2 Answers

Code error of Cannon IR3300 E000006-0000

getfile.asp?rid=1258 November 7, 2002 getfile.asp?rid=3215 Product : IR 2200 / 2800 / 3300 Title : E007 code for the IR 2200 / 2800 / 3300 Problem :
E007 code is occurring for the IR 2200 / 2800 / 3300

Solution :
In Service mode / Copier / Function / Part Check, energize M4 (the Fixing Drive motor). If the Fixing Drive motor does not come on, replace M4 (part number FH6-1848-000). Canon USA, Inc. Systems & Technical Support Division

you access service mode by pressing ADDITIONAL FUNCTIONS-2-8-ADDITIONAL FUNCTIONS

Apr 29, 2009 | Office Equipment & Supplies

Not finding what you are looking for?
Canon iR3035 Copier Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts


Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

2005 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides