Question about Epson Stylus Pro 4000 InkJet Printer

Open Question

The code Service REQ#0001001B Tells me headdriver temperature error ... How do I fix that. Performing a cleaning cycle is not the answer when you cant boot up the printer. Any help would be appreciat

I have taken out all the cartridges and cleaned the imput nozzles. I undid the screw and have cleaned the drain to the ink tank.(that was pretty messy) I soaked the sponge station with cleaner. The head is now sitting on a pad soaked in cleaner which I will leave overnight. But if that doesn't work what say you? The printer has performed wonderfully for years. Apart from a few heavy cleaning cycles and I did do a major head clean about 6 months ago it has had no problems.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
yooperbud
  • 8637 Answers

SOURCE: epson 440 won't print

The ink dried up in the print head. A printer should be used at least every two weeks to keep from drying up the ink. You may have to replace the print head or have it serviced.
This is not much help. Bud

Posted on Jan 25, 2009

Ad
  • 54 Answers

SOURCE: Can't perform a nozzle check - Sensor error load different paper

Hi tom_kolasa,


Here is the manual for your printer model. Epson Stylus Pro 9800 Printer Guide
http://files.support.epson.com/pdf/pro78_/pro78_gd.pdf

Hope that the manual contains everything you need from nozzle check to sensor errors.


Posted on Apr 09, 2009

  • 1 Answer

SOURCE: I have replaced the Epson ink cartridges for

I Have this problem too with the pink ink, ive replaced it and now it will not detect that there is even an ink cartridge in the printer at all...

Posted on Mar 20, 2010

Geekman
  • 32281 Answers

SOURCE: Can you Help me unclog

Inkjet printers need to be used frequently to prevent inkdrying out in the print head nozzles.
If the print head cleaning maintenance routine does not clear the blockages,then print head needs replacing, but it may be expensive.
It may be more cost effective to buy a later model and better printer thanreplace the print head.

Posted on May 18, 2011

SOURCE: I have Epson Stylus Pro

MAINTENANCE REQ - 0040 - Pump counter has reached predetermined amount. This parts/units need replacement >> Box Assy., Flushing Pump Unit Cleaner, Head, A, ASP Cleaner, Head, B, ASP Porous Pad, Box, FL, Upper Porous Pad, Box, FL, Lower >>and then Counters reset. Epson Stylus Pro 4800 ->Contact Support

Posted on Aug 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oven Lock stuck open before start of self-cleaning cycle I get a code F9, a flashing lock light, a continous beep and a dr code on the panel when I try to set self-cleaning cycle again.


Thank you for your inquiry, Lucie!

From what you have described your Frigidaire oven lock is stuck open and you are receiving error codes "F9" and "DR". The "F9" error code stands for runaway temperature (overheating). This could be an issue with your RTD (Resistance Temperature Detector) or the EOC (Electronic Oven Control). I would recommend performing a reset on your oven and you can do that by disconnecting from your oven for ten minutes. The "DR" code means that the door is not closed or the door latch is not recognizing the door is closed. This could be an issue with your door latch or control panel. If the reset does not help correct your issues I would recommend having a professional technician out to perform a proper diagnosis and repair. Best of luck! -Matt

Apr 30, 2015 | Frigidaire Stove/Oven/Range Black Glass...

1 Answer

All key pad works, except to clean oven. It double beep sound and nothing happens.


Hi Carol.

First make sure that you are performing clean procedure correctly. If you press both bake and broil and then self clean, then instead of self clean the oven will go in child lock beeping twice. Two beeps may also be result of incorrect temp calibration. Perform calibration as suggested in the extract from service manual below:

10_11_2011_1_11_07_pm.gif



Before starting the self clean cycle the electronic control (ERC) performs checkout of door latch and temperature sensor, lock motor is activated and both relay for bake and broil start the cleaning cycle. If one of the conditions is not met the electronic control will beep and you may get an error code.

Make sure that both bake and broil are working. If one of the two functions is not working, then one of the relays in the power board is likely faulty: If the oven is not heating at all , then problem is usually the oven sensor.

If the rest is working the problem can be the door lock motor. The relay board and control module may also be causing the problem. The oven must be tested.

This GE range is mostly electronic. Testing is mostly done following the diagnostic procedures suggested in the technical repair manual.

The first procedure is error code reading (user level). This consists in reading the error codes stored in the oven electronic control (AKA ERC).

Here an extract from service manual showing the procedure:


10_11_2011_12_33_32_pm.gif

The procedure can be found in the Service Manual at the bottom of this document. Check page 19 of the service manual.at the bottom of this document. When performing the test look for error FF and F2, which respectively mean door latch and oven sensor problem. (codes at page 24 of service manual.

After the error code test, test individually door latch, sensor and lock motor. Perform the tests at page 22 of manual:


10_11_2011_12_48_53_pm.gif10_11_2011_12_51_11_pm.gif

10_11_2011_12_52_43_pm.gif

If the test does not return any error, then the door latch and motor must be tested manually as explained at page 21 of service manual.

HERE THE COMPLETE SERVICE MANUAL IN PDF FORMAT (click to open).

Regards.

Ginko

Oct 11, 2011 | GE Profile JGBP79 Gas Kitchen Range

1 Answer

Frigidaire FEQ1442ES Electric Dryer not producing heat. Quits running part way through cycle... Lights flashing green.. Clothes never get dry. Code E95


Clogged Vent
If your dryer seems to run forever, it could be because of a clogged vent or internal ductwork. Your dryer may have an automatic cycle that turns off the dryer when the clothes are dry. It does this with a special thermostat or moisture-sensing system.
Normally, this is what happens during an automatic cycle:
The thermostat tells the dryer to heat until the interior of the dryer reaches a pre-set temperature--say 135 degrees.
When the dryer reaches the pre-set temperature, the thermostat tells the timer to begin advancing. (If there's a moisture sensor, the timer advances only if the moisture content of the clothing is low enough.)
The timer advances until the interior cools, then the thermostat tells the timer to stop advancing, and tells the dryer to start heating again.
This cycle continues until the clothes are dry. But...if the vent is clogged, the dryer may never reach the proper operating temperature, so it doesn't send the signal to the timer and the dryer continues to run indefinitely, even if the clothes are completely dry. To fix the problem, clean the vent and/or internal ductwork.
Heating Element
Your dryer's heating element may be partially burned out. If it is, your dryer still heats, but at such a low temperature that it takes three or four times as long to dry the clothes. If the element is partially burned out, replace the heating element. You can check for an ohm reading but will need to refer to the service manual for proper reading. This sometimes on the tech sheet located somewhere on the dryer. Usually between 9-13 ohms.
Cycling thermostat
Although this isn't a common problem, one of the thermostats that controls the temperature in your dryer may break and cause the dryer to heat poorly. If so, you need to replace it. The thermostat is usually a small, round, black device mounted to an oblong steel plate. The plate is mounted to the internal ductwork . This thermostat usually has four wires going to it. Check the 2 terminals that are opposite each other and are the closer together of the 2. These 2 terminals should have continuity. If not replace the thermostat.
This is a Free answer, Please rate me.

Oct 10, 2010 | Frigidaire FEQ1442ES Electric Dryer

1 Answer

EPSON 9800 foutmelding SERVICE CALL ERROR 0001001B


did you used a non-original ink cartridge? if you did your printer says"ERROR 0001001B" is print head error. need to be replaced, send to repair.

Aug 08, 2010 | Epson Stylus Pro 9800 InkJet Printer

1 Answer

Epson Stylus Pro 4000 got the 0001001B error, I tried to restart the machine, but the error still comes up.


When determining a solution for an error, always look to what changes you instituted just prior to the error. In my case, I switched from FW to USB. That brought on the 0001001b head driver (tg) temperature error. When I switched back to FW, the error went away and the SP4000 display reads "Ready"

Apr 19, 2010 | Epson Stylus Pro 4000 InkJet Printer

1 Answer

Stops near end of cycle and on/off light and drying high heat light flash


error code f08-htr relay stuck-ckeck htr not open citcuit-connections on board are clean especialy botton connecters-if still throws error then req new board

Nov 12, 2009 | Hotpoint Ariston Aquarius WD420 Front Load...

1 Answer

Stops printing half way through a canvas


The service manual says
"0001001B Head driver (TG) temperature error"
Head failure or head cable splicing defective/breaking of wire
Solution
 Head cable joint
 Head Assy exchange

You might try pausing the printer for 10 minutes, before it gets to the halfway point to let it cool down, then un-pause it.

You don't say how large the canvas is. If it is 44" by 60" or something large, above might be OK, if it is only 24" x16", it might be more trouble than it is worth, unless you are only printing a few.

Mar 24, 2009 | Epson Stylus Pro 10000 InkJet Printer

1 Answer

Turn the printer on and I get this message:


try this turn off the printer

then...

hold the power button and the pause button together, it enters factory rest mode

Mar 09, 2009 | Epson Stylus Pro 4800 InkJet Printer

2 Answers

Error c0998


That what service manual says:

Service Req xyyyy
A Controller error or print engine error detected. Turn off the printer. Wait at least 5 seconds and then turn it back on. If the error message still appears, write down the error number listed on the LCD panel (xyyyy) and turn off the printer, unplug the power cord, and contact a qualified service representative

Apr 29, 2008 | Epson Aculaser C1100 Printer

Not finding what you are looking for?
Epson Stylus Pro 4000 InkJet Printer Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18402 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...