- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There is not much the manual says about this problem. Although you could check if all contacts are clean and shiny. Also you should be sure, the battery door and the memory card door are closed correct. The sense contact behind the door, cold be dirty or oxidised. Try opening and closing several times. And what means fully charged? did you measure the outage? did you try these batteries in an other (similar) camera? When measuring the voltage of a battery, it should be higher then is printed on the battery, because a multimeter does not draw a current. The LP-E8 should at least give 7,3 to 7,5 volt on a multimeter.
This information expands upon the error code information contained in the Link 2000 Owner?s Manual.
E-01 Inverter high DC/Battery voltage shutdown Battery voltage has risen above 15.5 VDC for 12-volt models or 31 VDC for 24-volt models.
E-02 Inverter low DC/Battery voltage shutdown Battery voltage has dropped below 10 VDC for 12-volt units or 20 VDC for 24-volt units.
E-03 Inverter or Charger overtemp shutdown Unit will reset automatically after it has cooled sufficiently.
E-04 Battery overload Caused by excessively discharged batteries. See section in inverter owner?s manual titled ?Charging overdischarged batteries.?
E-05 AC Backfeed AC power from an outside source has been fed to the AC output of the inverter. Potentially damaging to the unit. Disconnect incoming AC power and correct the situation.
E-06 Electronic Overload Inverter overload caused by too large a load or a short circuit. Reset by cycling power switch or connecting incoming AC power.
E-07 Triac control error Triac has overheated. Shut down unit and allow to cool.
E-08 High battery voltage shutdown during charge mode Check all charging sources for proper voltage. Reset by cycling the power switch.
E-10 Link 2000 de-powered This indicates that power was removed and restored to the Link 2000.
E-12 Battery #1 voltage sense leads open Blue wire is not connected to battery #1.
E-13 Battery #2 voltage sense leads open Violet wire is not connected to battery #2. E-14 Inappropriate Charged V selected for sensed voltage This value defaults to 13.2 for a 12-volt system, 26.4 for a 24-volt system. If this setting is above the voltage limits of the charging source, this error code will be displayed. Please refer to page 9 of the Link 2000 Owner?s Manual
E-15 Incoming AC polarity reversed Check incoming AC wiring for a reverse polarity condition.
CCC Indicates battery being charged. Displayed when Time remaining is selected. LO BAT More than 50% of declared capacity of battery 1 or battery 3 has been consumed.
OL Meter reading out of range U xx Designates a user setup CEF. Please read the sections pertaining to CEF on pages 19?22. A Designates Alternator output current on a Link 2000-R. is a number from 1?200. P Indicates Percent of charge mode selected. is a number from 1?100.
The water drains into a drain pan that is usually located in the compressor compartmen on the back of the refrigerator. Most newer units you may not be able to remove it. But don't worry, the water in the drain pan will evaporate from the heat produced by the compressor and condenser coil. If you use too much water to clean the drain though, you van overfill it. So just use about two cups of really hot water and a flexible, snake like device ( I use 1/4 inch plastic water line or heavy weedwacker line ). Pour one cup into the drain and then use your snake device and gently run it down into the drain. If it is long enough and you can see where the drain tube drains into the pan, you want to be able to see the end of your snake device exit the drain. Try to break loose any debris and then remove your snake. Pour your second cup of hot water into the drain to flush out any debris and then you are all set.
the flashing indicates a past jam or safe sense turned off . you can reset the error by following the instructions in the owners manual. if you do not have manual go to www.fellowes.com , support and download the owners manual for your model.
The door catch/lock mechanism on the MX5 is liable to do this occasionally - if you keep trying to unlock it, it will open eventually (I manually pop the internal lock whilst opening the outer handle if that makes sense).
Once it's open though, you pretty much need to open up that door and replace the lock mechanism.
The top and bottom covers are also held together with plactic catches.
After you remove the battery, CD/DVD drive and hard drive etc.
start near an openning and gently pull apart the top and bottom cases, you should hear a click as a catch releases, then continue to work around the edge fron this point.