Question about Fusion Car Audio & Video

1 Answer

<!-- from fixya rte -->Do I need a amp for Fusion MS-BX402 speakers - Fusion Car Audio & Video

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 228 Answers

The reason for running an amp is becauze ur running your volume so loud you are getting distortion. Btw, its the distortion that damages speakers. If your happy with the sound then you dont need an amp. If your running your radio "full tilt" to get your sound, think about adding some power.

Posted on Dec 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fusion AT 1100 Flashes green power light once and then shuts down. Hiya I have checked all the wires again but no luck. I love this sub and do not have money to buy another one. Please help :-(


Amp is going into protect mide. This means either the amp has an internal fault or the speaker is blown. Pull the speaker out and disconnect the wires from it. Make sure they don't touch. If the amp powers up fine you know the speaker is bad. If it doesn't the amp is bad.

Jul 26, 2016 | Fusion Car Audio & Video

1 Answer

I have a 2 ohm dvc sub and a fusion pp am10001 amp what the best way to wire the sub to this amp


Since your amp is only 2 ohm stable, you will need to wire your 2 ohm DVCs in series (if they are 2 ohms each voice coil). Here is the manual for your amp:

http://www.vbc-group.com/ebay/PP%20Amp%20Man%20Pg1-21.pdf

Jan 09, 2016 | Fusion Car Audio & Video

1 Answer

How to connect two fpw 1200s to one amp


you need to bridge it. this will allow both speakers to be ran to the amp and it will distribute power from the amp evenly you should see a bridge port in your amp

Oct 27, 2013 | Fusion Car Audio & Video

1 Answer

Need factory stereo and speaker wiring diagram for '08 Ford Fusion


2008 Ford Fusion Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Blue/Red
Car Radio Accessory Switched 12v+ Wire: Green
Car Radio Ground Wire: Black/Blue
Car Stereo Antenna Trigger Wire: Purple/Black
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): White/Brown
Right Front Speaker Positive Wire (+): White/Purple
Right Front Speaker Negative Wire (-): White/Orange
Left Rear Speaker Positive Wire (+): Brown/Green
Left Rear Speaker Negative Wire (-): Brown/Yellow
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Brown/Blue

Feb 16, 2012 | 2006 Ford Fusion

1 Answer

Fusion amp soild bold red when the radio comes on


The amplifier is in protection mode.
3 reasons for this...

  1. Improper Load/overheat - wrong impedence voicecoils or wired improperly below rated impedence.
  2. Grounded Power - speaker wires touching, power wire touching ground,
  3. Internal component failure.
if the amplifier will still not go out of protect mode after removing the speakers and jumpering the remote wire to the + terminal - your amplifier needs professional repair.

Thanks for using FixYa - a good rating is appreciated for taking the time to answer your FREE question.

Jul 08, 2009 | Fusion Digital designs EN-AM6004 Car Amp

1 Answer

10 inch fusion amp


first of all your question is unclear, do you need speaker advise or amplifier advise

Feb 22, 2008 | Fusion Digital designs PP-AM8004 Car Audio...

1 Answer

Fusion sub..


check the impedenc on amp and speakers.if speakers have lower ohm the amp cant push them also can cause damage to amp.how do you have everything wired must be specific.high level inputs,rca,.how is the radio and amp wired together,where are you getting power sup[ply from and how?
chriszambrotta@yahoo.com

Jan 09, 2008 | Fusion FEW12PK Car Subwoofer

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fusion Car Audio & Video Experts

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Tygh Duval
Tygh Duval

Level 2 Expert

300 Answers

Are you a Fusion Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...