Question about Husqvarna Viking Emerald 116 Sewing Machine

2 Answers

THE CLOTH WILL NOT FEED ON MY MACHINE IF I USE ANY STITCH BUT A STRAIGHT STITCH.

I DON'T KNOW WHAT TO TRY

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Is it possible that you accidentally lowered the mechanism beneath the presser foot? Your manual will tell you how to lower and raise it. Are you using the same weight thread top and bottom? I use a "walking foot" to move upper and lower at the same rate when top stitching anything. Well worth the $$.

Posted on Dec 18, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Husqvarna Master
  • 7,365 Answers

It sounds like the machine needs to be checked to see if there is a problem with a part inside the machine

Posted on Dec 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The feed dogs on my sewing machine will not raise


if your question is that the fabric didn't feed when I tried a zig-zag stitch , well then this might be a normal thing to happen on your machine , some machines when set to MAX size zig-zag stitch retract the "feed dogs" as you call them so that the operator can hand move the fabric around under presser foot , this is task called "darn" and its usually for filling large holes in fabric (socks!!) and for adding embroidery too (special needle)

Oct 05, 2016 | Sewing Machines

2 Answers

Just received my machine and the fabric will not feed through.


It is likely that your feed dogs have been dropped. Try following the instructions listed in the attached link. It is also possible that something got jostled in shipping, and may need adjusting. If you can locate the feed dog drop mechanism and it is engaged, you may need to take your machine back to where you purchased it and have it replaced or adjusted.
How do raise or lower the feed dogs Brother

Nov 01, 2015 | Brother SE400 Computerized Embroidery and...

1 Answer

My straight stitch is not perfectly straight, what can I do?


1. Put a piece of paper on the sewing machine w/o thread. Sew for three inches.
2. Notice the needle holes are straight with the feed dogs. The pressure foot is not in line with the holes.
3. With the pressure foot down loosen the pressure foot pressure to it's lowest amount.
4. There is a screw on the arm that needs to be loosened. Afterwards, adjust the arm until the foot is parallel with the feed dogs. Tighten screw.
5. Try sewing again on the piece of paper to check for accuracy on being straight.
6. One other check is to insure the feed dogs have even wear.

Mar 04, 2015 | Brother CS-6000i CS6000i 60-Stitch...

1 Answer

THE CLOTH DOES NOT FEED WHEN I CHANGE FROM A STRAIGHT STITCH


Your pressure foot may need to be increased a little. When you change to a zigzag the distance is automatically decreased.You can increase the distance at the same time to overcome this problem.

Nov 30, 2014 | Husqvarna Viking Emerald 116 Sewing...

1 Answer

Feed dog


you can't sew a straight stitch without the feeddogs being in the up position, or it could break a needle and damage the machine.
so when the machine says put the feed dogs up it telling you
it can't sew a straight stitch with out them up

May 04, 2013 | Janome Sewing Machines

1 Answer

Brother VX 1090 lost manual


check with brother website first
Brother website
Brother home sewing & embroidery
Support- click on it
Find manuals & documentation--Download the latest product
Select home sewing & embroidery
Select model number & view
if they don't have one try these other
sites
sewingpartsonline.com
sewusa.com
sew4less.com

May 21, 2012 | Brother Sewing Machines

1 Answer

The lower side of thread is looping


Could be your bobben tension need reset.Try that and let me know if it helps.Good Luck.Don't give up!!!

Nov 27, 2011 | Singer 3116 Simple

2 Answers

I have a Totally Me Singer Sewing Machine and I don't have an instruction manual. I don't know how to thread the needle on the sewing machine. If you can help this would be great !


Try this link: http://www.singerco.com/accessories/instruction-manuals Type model no. in the search field and press Search. You'll be able to choose to pay or download for free! Good luck!

Aug 15, 2011 | Singer Zig Zag 727198 Sewing Machine

Not finding what you are looking for?
Husqvarna Viking Emerald 116 Sewing Machine Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Sewing Machines Experts

Douglas Plant
Douglas Plant

Level 2 Expert

194 Answers

Tally Girl
Tally Girl

Level 3 Expert

1133 Answers

Wayne Fellows
Wayne Fellows

Level 2 Expert

262 Answers

Are you a Husqvarna Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...