Question about Lenovo IdeaPad Computers & Internet

1 Answer

Idea pad z575 led fuse

Tried tracing the fuse but cant be sure which one it is i figure it will have number

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lenovo Master
  • 22,688 Answers

Doubt it.

Posted on Nov 30, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My main fuse on 900 vulcan 2011 keeps blowing just when I try to put it in. Does anybody have any ideas? this bike has very ow miles and is kept in guarage.


Low battery will not blow a fuse. If it blows right away when you turn on the ignition you have a main electrical short. Disconnect the regulator to the battery connector at the regulator to see if you have a shorted regulator. After the main fuse blows you should not have a battery drain so figure out also why your battery is discharged. Is your batttery no good. This would not blow a fuse in any case. Was the battery out recently, or disconnected. Make sure it is installed correctly and none of the wires are connected incorrectly. THEN you will have to start tracing the wiring from the main fuse to find the short circut.

Sep 12, 2014 | 2011 kawasaki Vulcan 900 Classic LT

1 Answer

Lenovo z575 Hotkeys Not Working


Go back to the Lenovo web-site for your specific model, and select the device-drivers for the "hot-keys". Download & install it.

Apr 04, 2014 | Lenovo IdeaPad Z575 1299-2AU Notebook PC -...

1 Answer

Video about how to fix a crayola light box


Does it have a replaceable bulb? If is LED then it might be done with unless the LED plugs in. Most people cant unsolder an replace them. Or it could be a bad switch

Mar 28, 2014 | Crayola Store Light Up Tracing Pad - Boy

1 Answer

Dead Lenovo IdeaPad Z575


Without seeing it, I cannot make a constructive comment. Sorry.

Mar 06, 2014 | Lenovo Ideapad Z575 129922u 15.6" Led...

1 Answer

I can't figure out why my trunk light in my 93


im not sure if its theres a fuse but make sure the bulb is good get a flashlight and make sure it is plugged in follow the wiring to make sure it is good and hooked up

Feb 13, 2013 | Cars & Trucks

1 Answer

I ne to figure out the frequency code for an Excalibur AL_700LC


The correct remote transmitter for the AL-700LC is the AU-3TLC. Unfortunately that particular remote is discontinued but there is a suitable replacement, AU-3TAL3. The AU-3TAL3 only differs in case style. The remote can be purchased from the Omega Research and Development, the makers of the AL-700LC, website.
The AU-3TLC and AU-3TAL3 are trinary (3-state) remote transmitters. Programming the remotes require the cutting of traces on the circuit board. On the back side circuit board, the side without the components, there are solder pads labeled 1 through 10. Each solder pad has to tracks / traces, one above and one below. The traces on the numbered side of the solder pad is the positive side. The inside trace, no number, is the negative side. When both traces for a particular pad is cut, the state is neutral. You need to match the cut traces exactly as your original remote.
The best way I have found to cut the traces is to use a dremel type tool. You can also use a tip of a knife, a scratch awl, or any sharp pointed tool to scratch the trace away until an open is achieved. Just be careful not to cut any traces that should not be cut.

Oct 15, 2012 | Vehicle Parts & Accessories

1 Answer

When i make a vector. the windo that pops up has tools of to the side. i cant get to them. ive tryed to min the windo,and strech it but that dont work. ive tryed a few things in computer settings but cant...


This a known issue. Backup your files. Uninstall the program. Restart. Download and install CCleaner to make sure that all traces of Corel Draw X4 are removed. Reinstall.

Please comment if the information provided has been helpful for the improvement of my support assistance. Thank you and regards.

May 09, 2010 | CorelDRAW Graphics Suite X4 for PC...

1 Answer

Cant figure out how to stop the timer before it goes out, or runs out of time


You should be able to hit the Stop pad, but you can download GE owner's manuals and installation instructions here.

If some of the pads on the keypad are not working, you may have a failed keypad, which can be replaced.

If so, please reply back with your model number and let us know.

Sep 28, 2008 | GE XL1800 1100 Watts Microwave Oven

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lenovo Computers & Internet Experts

Michael Vincent Cruz

Level 3 Expert

868 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18402 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Lenovo Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...