Question about KitchenAid Kitchen Aid K45SSWH Classic Tilt-Head Stand Mixer

1 Answer

Can I use lucas oil white lithium in my stand mixer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • KitchenAid Master
  • 1,238 Answers

They do not use oil at all, they use food grade grease. Any oil that is dripping out is the liquids separating out from the solids in the grease. You either need to open it up and stir the grease u again or remove the old grease completely and repack it with new stuff.

Posted on Nov 30, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 547 Answers

SOURCE: My kitchenaid stand mixer is leaking oil

First off -- if it's still under warrantee, you'll want to go to kitchenaid.com and find the nearest service center. The next thing I say starts with "void the warrantee" steps. :)

It's very simple to open a stand mixer to see if you've got a simple problem or a bad one.

Unplug it.

Follow the aluminum "Kitchen Aid" band to the back of the unit, there's one main screw. Remove this, and set it aside with the band which should come right off at this point.

Now, there should be two screws on each side of the unit where the band used to be. Remove each of these. They're all identical, so no worries if you mix them up.

Now you can lift the top off of the unit and see inside. The motor is at the back of the unit, the gear box at the front is where the oil is coming from. Try (GENTLY) to tighten the screws that hold the gearbox together. With a little luck, the gearbox screws had come loose and it was oozing oil out through the seals. If they're all firm, then you've got more serious problems and you'll want to find a service center for it.

Good luck!


Posted on Aug 03, 2009

  • 1 Answer

SOURCE: My stand mixer was stored on its side and leaked oil.

Called the Kitchenaid toll free number and found a local authorized repair center. Not a fixya solution, but at least a solution.

Posted on Oct 02, 2009

  • 130 Answers

SOURCE: My kitchenAid stand mixer is leaking oil. How do I

referring to:

http://shared.whirlpoolcorp.com/assets/pdfs/literature/Repair%20Part%20List%20-%204176924.pdf

You can see that there are 5 screws holding the upper and lower gearcase together. They pinch the gasket number 26 together and prevent the oil and grease from leaking. Remove the chrome ring by prying gently around the ring. You will see the 5 screw heads. Tighten them and the leaking will stop.

If it still leaks then you may have to replace the fiber washers number 29 which will involve disassembling the lower gear case.

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to add oil to cuisinart SM-55 stand mixer


The owners manual is available on the website. It doesn't mention anything about adding oil. What makes you think it needs oil. Mixer gears are usually lubricated with white grease and are maintenance free.

Nov 23, 2013 | Food Mixers

1 Answer

Oil leak


instead of putting a gasket on tell him to take out all of the old grease out that is what has broken down and turning into oil causing a leak and if he can repace the seal around the agitator shaft replace the old grease with a high temp bearing grease or a good quality lithium grease

May 25, 2010 | Hobart A200 Stand Mixer

1 Answer

Have an old hobart 140 mixer and i want to chang oil what kind of oil do i use


you need to replace it with a "FOOD-GRADE" mineral oil or FOOD-GRADE white lithium grease, you can get this from "Lubri-Plate" at their web-site

Nov 18, 2009 | Hobart D300 Stand Mixer

1 Answer

I have a H-600 Mixer, What oil should I use to top off the transmission?


either a 10wt food grade oil or a food grade white lithium grease whichever it uses now, but i don't suggest blending the two together

Oct 08, 2009 | Food Mixers

1 Answer

The mixer leaks oil around the shaft. Is this a user repairable problem? How do I find service centers?


Leaking of oil in a stand mixer is not necessarily indicative of a large problem.

Kitchenaid stand mixers are overpacked with oil to last the lifetime of the motor. If the motor sits idle for some time (is not used), the oil may begin to drip from the gears and settle. Oil leakage may primarily be seen from around the beater shaft or planetary action.

A stand mixer can lose up to a 1/4 cup of oil before it needs to be serviced.

It is recommended to run the mixer on speed 10 for 2 minutes in order to redistribute oil back into the motor. In order to prevent future occurences, this is recommended to be done every 3 weeks if mixer is not being used.
If you still feel as though the mixer is in need of service, you may locate Kitchenaid certified repair centers through the following link: http://caservice.kitchenaid.com/

Jul 10, 2009 | KitchenAid K45SS Classic Stand Mixer

1 Answer

Leaking oil


Leaking of oil in a stand mixer is not necessarily indicative of a large problem.

Kitchenaid stand mixers are overpacked with oil to last the lifetime of the motor. If the motor sits idle for some time (is not used), the oil may begin to drip from the gears and settle. Oil leakage may primarily be seen from around the beater shaft or planetary action.

A stand mixer can lose up to a 1/4 cup of oil before it needs to be serviced.

It is recommended to run the mixer on speed 10 for 2 minutes in order to redistribute oil back into the motor. In order to prevent future occurences, this is recommended to be done every 3 weeks if mixer is not being used.

Jun 27, 2009 | KitchenAid Classic Stand Mixer

1 Answer

My mixer is leaking oil. last time we made bread dough in it it sounded kind of rough. we figured wiyh the heavy load maybe that was the rteason for the noise. when we moved the mixer to clean it, there...


Leaking of oil in a stand mixer is not necessarily indicative of a large problem.

Kitchenaid stand mixers are overpacked with oil to last the lifetime of the motor. If the motor sits idle for some time (is not used), the oil may begin to drip from the gears and settle. Oil leakage may primarily be seen from around the beater shaft or planetary action.

A stand mixer can lose up to a 1/4 cup of oil before it needs to be serviced.

It is recommended to run the mixer on speed 10 for 2 minutes in order to redistribute oil back into the motor. In order to prevent future occurences, this is recommended to be done every 3 weeks if mixer is not being used.

May 13, 2009 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

KitchenAid 250 Watts; Classic: Leaking Oil


Found this,may be helpful.
Why do I see oil leaking from the beater shaft of my stand mixer?
Some KitchenAid® stand mixers that are not used very often or have been tipped may experience slight oil leakage from the shaft or hub attachment. To avoid the oil leakage, KitchenAid suggests that you run the mixer weekly for short periods of time. Generally, the mixer may lose approximately X cup of oil before repair is necessary. The oil used is FDA approved and is not harmful to consume, should any get into the food that you are preparing.
.

Dec 15, 2008 | KitchenAid K45SS Classic Stand Mixer

1 Answer

K45SS leaks lubricant


Leaking of oil in a stand mixer is not necessarily indicative of a large problem.

Kitchenaid stand mixers are overpacked with oil to last the lifetime of the motor. If the motor sits idle for some time (is not used), the oil may begin to drip from the gears and settle. Oil leakage may primarily be seen from around the beater shaft or planetary action.

A stand mixer can lose up to a 1/4 cup of oil before it needs to be serviced.

It is recommended to run the mixer on speed 10 for 2 minutes in order to redistribute oil back into the motor. In order to prevent future occurences, this is recommended to be done every 3 weeks if mixer is not being used.
Exploded parts views for all mixers are available at www.kithchenaid.com. Click "Customer Care" in the upper right hand corner of the main page, and then select "Locate Manuals and Guides." You will need to enter the unit's model number exactly as it appears on the bottom of the mixer. It will be listed on a white sticker.

Nov 03, 2008 | Food Mixers

1 Answer

Oil leak


hi,its no big deal--the mixer is filled with grease and its coming from the planetary.if it is bothersome remove the drip cup (silver ring) then you will see a roll pin that holds the planetary onto the main shaft.get a small punch and knock out the pin.if the planetary doesnt drop down use 2 flat head scewdrivers and pry it down.clean out the old grease and put in new grease.you can buy it from hobart or get a white lithium grease from an auto parts store.

Oct 23, 2007 | Hobart N50 Stand Mixer

Not finding what you are looking for?
KitchenAid Kitchen Aid K45SSWH Classic Tilt-Head Stand Mixer Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Mixers Experts

Appliance engineer

Level 2 Expert

87 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a KitchenAid Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...