Question about Neptune Washing Machines

1 Answer

My Neptune fav6800aww not spinning out

Nothing so far

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 150 Answers

A few issues are known on these machines, there was a replacement tub displacement sensor to correct error codes, #12002194, and the more common issue preventing spinning would be a failed clutch pulley pack, #12002211. Pleazer Appliance...

Posted on Dec 20, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

namzyanzy
  • 435 Answers

SOURCE: Excessive wobble

If there's a loud thumping noise during the spin cycle, the load of clothes has probably gotten unbalanced. Open the lid, redistribute the clothes in the washer, then re-start it. Repeat these steps if necessary.

Posted on Sep 06, 2008

dh1200s
  • 335 Answers

SOURCE: how to get front panel off neptune fav6800aww washing machine

Just a quick search in this forum fot "Front Panel" returned this post which says it better then I could.

http://www.fixya.com/support/t538238-remove_front_panel

Posted on Jan 18, 2009

dh1200s
  • 335 Answers

SOURCE: maytag neptune fav6800aww wont spin on rinse cycle

With this post I’m attempting to enhance the troubleshooting process regarding dc/UC errors in Spin Cycle associated with the FAV6800A machine. The troubleshooting steps are more to help DIY owners but it could be good info. for other owners to pass along to their appliance repair service if you go forward with a repair. I’m a DIY’er who refused to junk my machine as long as parts cost did not trigger a replacement decision and I have some basic mechanical skills. What I have learned about these fail codes, dc/UC in Spin Cycle is…. this is a chronic failure condition associated with the FAV6800A series machine (no brainer per numerous posts in this forum) and I feel that most of the time these codes are associated with a clutch malfunction.
The troubleshooting guide packed in the console of your machine makes reference to this issue in the Will Not Spin section of the guide and states to replace the clutch. I re-lubed my clutch with WD-40 and I have been working with 30+ loads of varying size with no Spin Cycle errors since early December 08. I and two other DIY forum members found this issue to be a maintenance issue with the clutch, no out of pocket cost for me and I’m sure under $5 for the other two forum members, I had a can of WD-40 in the house. See the links I have attached within this post. There is a description of the clutch removal I did in those posts. I hope this works for others; I’m sure many of these machines head to the curb for bulk trash pickup. Maybe you can extend the service life of your $1K machine if this proves to be a clutch re-lube fix for this issue. Shame on Maytag for not placing a quality sealed bearing in the clutch…. my opinion.
1. Raise the top of the machine. Insert a flat blade putty knife approximately 2.5” from the left and right sides of the washer top, depress the spring tabs securing machine top to the washer base. Raise the top of the machine to observe the wash basket and tumbler action described in step 2...

2. With the top raised start a Spin Only cycle with no clothes in the wash basket, observe the wash basket it will begin to rotate CCW. Watch the tumblers, they should not rotate in spin cycle (maybe ½ turn at the start of spin cycle and that’s all). If the tumblers rotate while the wash basket is rotating you have a clutch malfunction and the Spin Cycle will fail with dc/UC errors. If this is not the situation move on to step 3. I need to post step 3 and the rest of this post in a comment.

Posted on Jan 30, 2009

FAV6800AWDIY
  • 526 Answers

SOURCE: maytag washer top load neptune

See this post for troubleshooting the Lr error code. . http://www.fixya.com/support/t2419091-maytag_neptune_top_load_fav6800aww_tub

Lr is locked rotor. My first thought was that this could be a Motor Controller issue. This owner replaced tried that and it did not resolve the issue. He then replaced the main Control Board and that fixed his machine. Without known good parts (Control Board Motor Controller) this might be difficult for a DIY fix.

The Service Manual for reference. Sears Parts Direct for reference.

If you are going to try to DIY the repair I will see if I can help……Rich

Posted on Apr 28, 2010

FAV6800AWDIY
  • 526 Answers

SOURCE: maytag neptune top loader model fav6800aww has an

See if this post http://www.fixya.com/support/t4757262-i_have_a_letter_showing_and_it_say_o_d_w will get you started.


You have lost signaling from the Left Hand Lid Lock. If you want to DIY I will try to help........Rich

Posted on May 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have Neptune FAV6800AWW top load, washes when it gets to the rinse cycle it stops with water in. If we remove the clothes and wait a while we can get it to complete. The code we are getting is DR which...


Are you sure the error code is DR? Could it be DC an unbalance error code. Google ""16022808.pdf"" to find. Is the washer banging around in Spin Cycle? If so this is a Clutch Pulley issue.

Google this ""Neptune TL Washer FAV6800AWW"" a forum where I help owners of the FAV6800A and FAV9800A machines.

DR is not a listed error code in the FAV6800A/FAV9800A Service Manual.

Aug 27, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Model fav6800aww drains during the wash and rinse cycle but does not drain during the spin cycle. it give an dc code during the spin cycle which i know that means unbalance but what does that have to do...


Clutch issue and possible time for a tub seal replacement

Google this for a post that covers the Clutch removal and inspection/repair;

""Neptune TL Washer FAV6800AWW"" you will find the Service Manual in post 5 of that sticky.

Google this for Outer Tub bearing rebuild;""
FAV6800A/FAV9800A Outer Tub bearing replacement""

Aug 20, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Once washer hits spin cycle (12 min. left) it throws a DC code. Checked the TDS sensor - OK, motor control - OK, spinning the tub by hand in CCW feels smooth. Haven't taken apart to clean and lube...


This is a Clutch issue.

Google this; Neptune TL Washer FAV6800AWW

This is a DIY Appliance repair forum and you can get the Service Manual and owner repair support at that site..

In the Sticky: Neptune TL Washer FAV6800AWW 5 post down you will find a link to the Service Manual. You absolutely need the Service Manual to DIY issues with the machine. It's not the best SM but will get you started. I also have repair post in that sticky to help with the most common issues (this issue) that I have helped owners with. I'm an owner of a FAV6800AWW top load machine.
I can

Apr 22, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

I have a Maytag Neptune TL ( Model # FAV6800AWW) washing machine does spend but clothes still soak after it done. when you spend it by hand, it only spend in counterclockwise.


Any error codes. What happens if you start a Spin Only Cycle witht the same load? Does the times stay stuck at xx minutes in the LED display and the machine constantely starts and stops?

The more info on your problem the better.

Do you want to DIY the fix? Google this; Neptune TL Washer FAV6800AWW see the 5th post down here for general info and the Service Manual. If you want to try to DIY the repair I will help.

Apr 04, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

I keep getting error code dc and it wont spin


Somewhere on this forum I have a response to DC or UC unbalance errors and the fix. It's hard to find my past post on this forum.

Google this; Neptune TL Washer FAV6800AWW

This is a DIY Appliance repair forum and you can get the Service Manual and repair support posted in the sticky at that site.

In the Sticky: Neptune TL Washer FAV6800AWW 5 post down you will find a link to the Service Manual. You absolutely need the Service Manual to DIY issues with the machine. It's not the best SM but will get you started. I also have repair post in that sticky to help with the most common issues that I have helped owners with. I'm an owner of a FAV6800AWW top load machine.

Apr 03, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

GETTING DC ERROR CODE WITH A GRINDING SOUND AND THEN IT STOPS COMPLETELY


The DC error code is 9 time out of 10 caused by a Clutch Pulley malfunction. The grinding may ne Outer Tub Bearings but need more info. Open the Washer Lid. Spin the wash basket CCW. Do you hear and grinding noise?

The noise may be coming from under neath the tumblers. Further troubleshooting is required.

Do you have basic DIY mech. skills and do you want to save your $1K machine?

If so Google Neptune TL Washer FAV6800AWW

In the Sticky: Neptune TL Washer FAV6800AWW 5 post down you will find a link to the Service Manual. You absolutely need the Service Manual to DIY issues with the machine. It's not the best SM but will get you started. I also have repair post in that sticky to help with the most common issues that I have helped owners with. I'm an owner of a FAV6800AWW top load machine.


Good luck.

Mar 17, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

My MAytag will not spin the water outta my clothes on spin cycle


If you machine is a FAV6800A or FAV9800A don't worry about the last two letters of the model number.

Google this; Neptune TL Washer FAV6800AWW

This is a DIY Appliance repair forum and you can get the Service Manual and repair support at that site..

In the Sticky: Neptune TL Washer FAV6800AWW 5 post down you will find a link to the Service Manual. You absolutely need the Service Manual to DIY issues with the machine. It's not the best SM but will get you started. I also have repair post in that sticky to help with the most common issues that I have helped owners with. I'm an owner of a FAV6800AWW top load machine.

If you need help post in the Maytag/Magic Chef/Admiral/Jenn-Air forum with your issue and we will try to help.

Feb 28, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Neptune top load washer model # fav6800aww will not drain and spin if anything is in it, remove all articles and it will drain and spin


Are yiy failing in Spin Cycle wuth dC or uC error codes?

If so see if this post Clutch Fix. There is a link to the SM.....D*ick

Sep 18, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Excessive wobble


If there's a loud thumping noise during the spin cycle, the load of clothes has probably gotten unbalanced. Open the lid, redistribute the clothes in the washer, then re-start it. Repeat these steps if necessary.

Sep 06, 2008 | Maytag Neptune Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Neptune Washing Machines Experts

Cleverer2

Level 2 Expert

298 Answers

Terry Hair

Level 3 Expert

4128 Answers

ray gallant

Level 3 Expert

43003 Answers

Are you a Neptune Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...