What does the code 33 mean

Codes 32 to 35

These codes are signaled by three flashes, a two-second pause and the number of flashes that corresponds to the second digit. Code 32 (triple flash, pause, two flashes) means the driver side airbag has a circuit open or with high resistance, Code 33 (triple flash, pause, two flashes) means the passenger side airbag has a circuit open or with high resistance, Code 34 (triple flash, pause, four flashes) means the driver side airbag has a shorted circuit or one with low resistance and Code 35 (triple flash, pause, five flashes) means the passenger side airbag has a shorted circuit or one with low resistance.

I personally would let some one who knows what they are doing look at it. Grounding or feeding the wrong wire could set off an air bag and hurt someone.

Mercury Grand Marquis diagnostic code 33 Questions ...

www.fixya.com > ... > diagnostic code 33 > Cars & Trucks > Mercury

Mercury Grand Marquis cars & trucks diagnostic code 33 questions and ... 2006Mercury Grand Marquis air bag light flashes ... What does code po1151 mean.

2006 Mercury Grand Marquis air bag light flashes three ...

www.fixya.com/.../t19845434-2006_mercury_grand_marquis_air_bag_l...

Sep 3, 2013 - It then stay on. I assume - Mercury 2006 Grand Marquis question. ...What does a flashing air bag light mean on a 1993 Grand Marquis? Jul 23 ...

Mercury Grand Marquis airbag code 33 Questions ... - Fixya

www.fixya.com > ... > Tags > airbag code 33 > Cars & Trucks > Mercury

Mercury Grand Marquis cars & trucks airbag code 33 questions and answers. ... What does a flashing air ... 2006 Mercury Grand Marquis air bag light flashes.Missing: mean

Each code has multiple diagnosis.
You'll need to figure which it is.

The codes mean the following (each code has more than one diagnosis)

23 = Front injector open/low
23 = Front injector high

32 = Rear injector open/low
32 = Rear injector high
32 = Alarm output high

33 = System relay contacts open
33 = System relay coil high/shorted
33 = System relay coil open/low
33 = System relay contacts closed

Mitsubishi TV troubleshooting
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

I'm going to take a wild guess and say you have a Chrysler product.
Chrysler and Dodge use two digit codes, and 55 means you have reached the end of the self-test.
So code 32 would be a problem with the EGR system, and code 33 would be a problem with the ac compressor clutch.
There is no code 2.

Goto Main Menu > Options > Cheats > Enter Cheat in game. Use the following codes ( R - Red, G - Green, O - Orange, B - Blue, Y - Yellow ), without strumming.

Unlock everything (no audio will play when entering this code)[GRBO] [GRYB] [GRYO] [GBYO] [GRYB] [RYBO] [GRYB] [GYBO] [GRYB] [GRYO] [GRYO] [GRYB] [GRYO]Unlocks All SongsYO,RB,RO,GB,RY,YO,RY,RB,GY,GY,YB,YB,YO,YO,YB,Y,R,RY,R,Y,O
Codes pulled from Gamefaqs. They're an awesome website for game cheats, reviews, walkthroughs, etc.

Have fun!

If you counted the flashes as you are listing them then this would be a code 33, this code 33 is defined as vechile speed sensor, this is the speed sensor and is located on the transmission, checcck the connection to the sensor and if the connector and the connection is good then i would replace the sped sensor.

Code 12 is only displayed when outputting "flash codes" (Cycling the key and watching the Check Engine Light flash) - it mostly indicates that the diagnostic system is functioning properly. There is only a problem if you don't get this code.

Codes 13 and 14 are both MAP Sensor codes.

Codes 24 and 26 are both Secondary Air Switching Solenoid codes.

Code 33 is an A/C Presure sensor circuit code.

Flash codes are pretty generic. They tell you that there is a failure in a particular system, but they don't specify what type of failure. Flash Code 14 for example, can mean that the Map Sensor Voltage is too high or it can mean that it is too low, or it can mean that the 5 volt reference voltage is shorted to ground.

"P-codes" (The kind you must have a scanner to get) however, are more descriptive. Those will give you a more accurate description of what exactly is the problem with the system that has failed.

I will advise you however, that all of these codes can be caused by a shorted VREF. (5 Volt Reference Circuit) Find out where it is shorted and you will most likely fix all of these codes with one repair.

is gas in it?