Question about Monster Cable MCC AVL300-S Remote Control

1 Answer

Mine just stopped working. Can it be reset?

Took the battery off and put it back in. No change.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Monster Cable Master
  • 75,417 Answers

Take the battery out from it compartment. The remote control will reset itself after some time. The re-insert the batteries, and check the remote control for its infra-re emission.
Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician.

Posted on Nov 24, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kenwood kdc 136 works normal for ten minutes then stops and displays ;ocer


I had an issue like this took me months to fix it. I finally just put in a higher grade fuse in. I think it had a 10 and i put in a 15 worked after that but mine was not wired to the battery. I would say check your fuses and wires.

Apr 20, 2014 | Kenwood KDC-138 FM / AM Receiver

1 Answer

Wall Clock Won't Keep Time


Disconnect it. Plug it back in. Go to the office and tell the master clock to reset all the clocks. It sounds like it is searching for guidance from the master unit.

these people may be able to help specifically if you don't have instructions for the master unit.

http://stevenengineering.com/tech_support/PDFs/57MAIN_CLOCKS-TIME-SYSTEMS.pdf

This is the way I did it when we have all the clocks in a hundred room hotel to change when the clocks change in the UK. I went back to the same hotel 35 years later and asked if I could see when the cupboard where the clock was reset, and the unit was still there, albeit not working. It was replaced for a more modern system, of putting clock radios in rooms.

Aug 19, 2017 | Dukane Audio Players & Recorders

1 Answer

My LG Viper phone just stopped working,


Mine does this often. Sometimes it's so dead that it has to blink for a little while before being able to boot back up.

Sep 23, 2012 | Sprint LG Viper 4G LTE GSM Smartphone -...

5 Answers

Skyscan Atomic Clock WWVB


figure out where yu are north south west east zones on your map from where yu are , then pull battery again it should stop at for eight or twelve push time zone then set in a window facing your zone it should automatically pick it up shortly in awhile
sw i think it may stop at four also but then wait

Oct 14, 2008 | SkyScan 86709 Atomic Wall Clock

2 Answers

My Rainbow stopped running


I took my unit apart to clean it. I was careful to put it back the same way. Now it won't start.

Jul 07, 2008 | Rainbow E series Canister Wet/Dry Vacuum

4 Answers

Camera won't zoom in


Mike,

I don't think it is your BB. Mine too has stopped zooming when it worked fine last week.

Do you know if BB did an auto update to the software. I am not aware of any.

S217497

Mar 28, 2008 | RIM BlackBerry Pearl 8100

1 Answer

Samsung S730 problem.


Mine did that. I just took the batteries out and kept them out for a few minutes when I put them back in it stopped. I think I turned the settings around a few times after I took the batteries out.

Mar 03, 2008 | Samsung Digimax S730 Digital Camera

1 Answer

MyFi remote control has stopped working


ok take the battery out of the radio then put it back in and it should work mine did the same thing to me

Nov 24, 2007 | Delphi MyFi SA10113 XM Radio Receiver with...

17 Answers

Wont turn on


take the battery out and put it back in. try replacing the battery

Oct 10, 2007 | Samsung UpStage SPH-m620 Cellular Phone

4 Answers

The scroll wheel won't work


Mine also stopped functioning so took it to a camera repair shop. The shaft had broken and had to be replaced. It cost me approx a sixth of the price of the camera.

Mar 11, 2007 | Fuji FinePix S9000 Zoom Digital Camera

Not finding what you are looking for?
Monster Cable MCC AVL300-S Remote Control Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Monster Cable Televison & Video Experts

jairo sanchez

Level 2 Expert

276 Answers

john h

Level 3 Expert

14343 Answers

The Knight
The Knight

Level 3 Expert

75417 Answers

Are you a Monster Cable Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...